Hi All,
I need help with my Turris Mox. I have Module A + G + E for my setup and I have done rescude mode 4 through USB. After rescude mode 4 my Turris Mox does not seems to work and now my Turris Mox keep on having steady red LED light on Module A and red LED 2 light on Module G and LAN is not working as well on the module E.
What should I do?
I should add that I have also tried Rescude Mode 6 and I have similar result. Upon finishing the rescude mode 4 or 6, Mox will reboot and it will blink twice for two times and then it reboots again in infinite loop. If I unplug and plug it back in to the power source, the LED light keep showing steady light no blinking or heart beat.
Any clue guys?
Try to run only A + E, without G modul.
Tried your suggestion and it does not work as well. Here are some videos including reflashing.
Try to connect to your router via serial cable …
It says more …
This is what I am getting:
U-Boot 2018.11 (Dec 03 2018 - 09:33:41 +0000)
DRAM: 1 GiB
Enabling Armada 3720 wComphy-0: SGMII1 3.125 Gbps
Comphy-1: PEX0 5 Gbps
Comphy-2: USB3_HOST0 5 Gbps
MMC: sdhci@d8000: 0
Loading Environment from SPI Flash… SF: Detected w25q64dw with page size 256 B ytes, erase size 4 KiB, total 8 MiB
OK
Model: CZ.NIC Turris Mox Board
Net: eth0: neta@30000
Turris Mox:
Board version: 22
RAM size: 1024 MiB
Serial Number: 0000000D300006CF
ECDSA Public Key: 02002c51c54bdfbb0770c5d8f2d06e8add086d4720a8318cfb5ff09366dc da71e755cec484bec0ed6695a200dbd92a6de829774701b6b1b296fba95da512176ce9069a
SD/eMMC version: SD
Module Topology:
1: Passthrough Mini-PCIe Module
2: Peridot Switch Module (8-port)Hit any key to stop autoboot: 0
gpio: pin GPIO221 (gpio 57) value is 0
gpio: pin GPIO220 (gpio 56) value is 1
neta@30000 Waiting for PHY auto negotiation to complete… TIMEOUT !
neta@30000: No link.
aes - AES 128 CBC encryptionUsage:
aes enc key iv src dst len - Encrypt block of data $len bytes long
at address $src using a key at address
$key with initialization vector at address
$iv. Store the result at address $dst.
The $len size must be multiple of 16 bytes.
The $key and $iv must be 16 bytes long.
aes dec key iv src dst len - Decrypt block of data $len bytes long
at address $src using a key at address
$key with initialization vector at address
$iv. Store the result at address $dst.
The $len size must be multiple of 16 bytes.
The $key and $iv must be 16 bytes long.
Wrong Image Format for bootm command
ERROR: can’t get kernel image!
=>
May I have a question if you didn’t try to use an experimental workaround for reboots? When yes, is there possible to use the latest version?
Yes it is still based on original UBoot. Any dummy guide on what I should do to update, quite new to this serial thing.
Ok, I tried to update the UBoot and now I am getting the following below with SD Card inserted.
Initializing DDR… done
U-Boot 2020.07-rc5-00082-g46bc60abad (Nov 06 2020 - 11:58:20 +0100)
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
Comphy-0: SGMII1 3.125 Gbps
Comphy-1: PEX0 5 Gbps
Comphy-2: USB3_HOST0 5 Gbps
MMC: sdhci@d8000: 0
Loading Environment from SPI Flash… SF: Detected w25q64dw with page size 256 Bytes, erase size 4 KiB, total 8 MiB
OK
Model: CZ.NIC Turris Mox Board
Net: eth0: neta@30000
Turris Mox:
Board version: 22
RAM size: 1024 MiB
Serial Number: 0000000D300006CF
ECDSA Public Key: 02002c51c54bdfbb0770c5d8f2d06e8add086d4720a8318cfb5ff09366dcda71e755cec484bec0ed6695a200dbd92a6de829774701b6b1b296fba95da512176ce9069a
SD/eMMC version: SD
Module Topology:
1: Passthrough Mini-PCIe Module
2: Peridot Switch Module (8-port)Hit any key to stop autoboot: 0
gpio: pin GPIO221 (gpio 57) value is 0
gpio: pin GPIO220 (gpio 56) value is 1
neta@30000 Waiting for PHY auto negotiation to complete… TIMEOUT !
neta@30000: No link.
Unknown command ‘aes’ - try ‘help’
Wrong Image Format for bootm command
ERROR: can’t get kernel image!
Just to add this is what I get if I connect for network boot to Turris Omnia.
U-Boot 2018.11 (Dec 16 2018 - 12:50:19 +0000), Build: jenkins-turris-os-packages-kittens-mox-90
DRAM: 1 GiB
Enabling Armada 3720 wComphy-0: SGMII1 3.125 Gbps
Comphy-1: PEX0 5 Gbps
Comphy-2: USB3_HOST0 5 Gbps
MMC: sdhci@d8000: 0
Loading Environment from SPI Flash… SF: Detected w25q64dw with page size 256 Bytes, erase size 4 KiB, total 8 MiB
OK
Model: CZ.NIC Turris Mox Board
Net: eth0: neta@30000
Turris Mox:
Board version: 22
RAM size: 1024 MiB
Serial Number: 0000000D300006CF
ECDSA Public Key: 02002c51c54bdfbb0770c5d8f2d06e8add086d4720a8318cfb5ff09366dcda71e755cec484bec0ed6695a200dbd92a6de829774701b6b1b296fba95da512176ce9069a
SD/eMMC version: SD
Module Topology:
1: Passthrough Mini-PCIe Module
2: Peridot Switch Module (8-port)Hit any key to stop autoboot: 0
gpio: pin GPIO221 (gpio 57) value is 0
gpio: pin GPIO220 (gpio 56) value is 1
neta@30000 Waiting for PHY auto negotiation to complete… done
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.2.101 (252 ms)
Using neta@30000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.101
Filename ‘/turris-netboot/mox_0000000D300006CF’.
Load address: 0x4e00000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
4.3 MiB/s
done
Bytes transferred = 16078800 (f557d0 hex)Loading kernel from FIT Image at 08000000 …
Using ‘conf@1’ configuration
Trying ‘kernel@0’ kernel subimage
Description: Linux kernel without
Created: 2019-08-09 17:19:06 UTC
Type: Kernel Image (no loading done)
Compression: uncompressed
Data Start: 0x080000ec
Data Size: 10027016 Bytes = 9.6 MiB
Hash algo: crc32
Hash value: dff1ba29
Hash algo: sha1
Hash value: 4be075ef46c2c3c041fad321cc2aa74d41015889
Verifying Hash Integrity … crc32+ sha1+ OKLoading ramdisk from FIT Image at 08000000 …
Using ‘conf@1’ configuration
Trying ‘ramdisk@0’ ramdisk subimage
Description: initramfs
Created: 2019-08-09 17:19:06 UTC
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x0899021c
Data Size: 6030336 Bytes = 5.8 MiB
Architecture: AArch64
OS: Linux
Load Address: unavailable
Entry Point: unavailable
Hash algo: crc32
Hash value: 4c0a37bf
Hash algo: sha1
Hash value: f2a65e2921a2de34fb7e77856bbbc3909d773372
Verifying Hash Integrity … crc32+ sha1+ OKLoading fdt from FIT Image at 08000000 …
Using ‘conf@1’ configuration
Trying ‘fdt@0’ fdt subimage
Description: Flattened Device Tree blob
Created: 2019-08-09 17:19:06 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x08f50728
Data Size: 19292 Bytes = 18.8 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: d2d271e7
Hash algo: sha1
Hash value: 71a1b91456959620837fa45cb168dd06825b6c60
Verifying Hash Integrity … crc32+ sha1+ OK
Booting using the fdt blob at 0x8f50728
Loading Kernel Image … OK
Loading Ramdisk to 3b95e000, end 3bf1e400 … OK
Loading Device Tree to 000000003b956000, end 000000003b95db5b … OKStarting kernel …
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.134 (beast@slave10) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 66cacd7)) #0 SMP Tue Aug 6 09:06:21 2019
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] Machine model: CZ.NIC Turris Mox Board
[ 0.000000] earlycon: ar3700_uart0 at MMIO 0x00000000d0012000 (options ‘’)
[ 0.000000] bootconsole [ar3700_uart0] enabled
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] random: get_random_bytes called from start_kernel+0x80/0x460 with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu s29464 r8192 d31976 u69632
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line: console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 1014296K/1048576K available (6974K kernel code, 448K rwdata, 2016K rodata, 320K init, 316K bss, 34280K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008750000 ( 6976 KB)
[ 0.000000] .rodata : 0xffffff8008750000 - 0xffffff8008950000 ( 2048 KB)
[ 0.000000] .init : 0xffffff8008950000 - 0xffffff80089a0000 ( 320 KB)
[ 0.000000] .data : 0xffffff80089a0000 - 0xffffff8008a10008 ( 449 KB)
[ 0.000000] .bss : 0xffffff8008a10008 - 0xffffff8008a5f108 ( 317 KB)
[ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf01000000 ( 16 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc040000000 ( 1024 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000005] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.008416] Console: colour dummy device 80x25
[ 0.012924] Calibrating delay loop (skipped), value calculated using timer frequency… 25.00 BogoMIPS (lpj=125000)
[ 0.023574] pid_max: default: 32768 minimum: 301
[ 0.028426] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.035259] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.043623] ASID allocator initialised with 32768 entries
[ 0.049200] Hierarchical SRCU implementation.
[ 0.054065] smp: Bringing up secondary CPUs …
[ 0.058997] Detected VIPT I-cache on CPU1
[ 0.059027] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
[ 0.059058] CPU1: Booted secondary processor [410fd034]
[ 0.059169] smp: Brought up 1 node, 2 CPUs
[ 0.079876] SMP: Total of 2 processors activated.
[ 0.084724] CPU features: detected feature: GIC system register CPU interface
[ 0.092062] CPU features: detected feature: 32-bit EL0 Support
[ 0.098072] CPU features: detected feature: Kernel page table isolation (KPTI)
[ 0.107879] CPU: All CPU(s) started at EL2
[ 0.112024] alternatives: patching kernel code
[ 0.117205] devtmpfs: initialized
[ 0.122870] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.132955] futex hash table entries: 512 (order: 4, 65536 bytes)
[ 0.139333] xor: measuring software checksum speed
[ 0.244231] 8regs : 1918.800 MB/sec
[ 0.344263] 8regs_prefetch: 1710.400 MB/sec
[ 0.444299] 32regs : 2358.800 MB/sec
[ 0.544334] 32regs_prefetch: 1984.400 MB/sec
[ 0.549001] xor: using function: 32regs (2358.800 MB/sec)
[ 0.554568] pinctrl core: initialized pinctrl subsystem
[ 0.560662] NET: Registered protocol family 16
[ 0.566313] cpuidle: using governor ladder
[ 0.570537] vdso: 2 pages (1 code @ ffffff8008754000, 1 data @ ffffff80089a4000)
[ 0.578297] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.585820] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 9, base_baud = 0) is a mvebu-uart
[ 0.594744] console [ttyMV0] enabled
[ 0.594744] console [ttyMV0] enabled
[ 0.602067] bootconsole [ar3700_uart0] disabled
[ 0.602067] bootconsole [ar3700_uart0] disabled
[ 0.791738] raid6: int64x1 gen() 320 MB/s
[ 0.961672] raid6: int64x1 xor() 318 MB/s
[ 1.131797] raid6: int64x2 gen() 518 MB/s
[ 1.301840] raid6: int64x2 xor() 451 MB/s
[ 1.471859] raid6: int64x4 gen() 781 MB/s
[ 1.641980] raid6: int64x4 xor() 552 MB/s
[ 1.812023] raid6: int64x8 gen() 938 MB/s
[ 1.982121] raid6: int64x8 xor() 563 MB/s
[ 2.152240] raid6: neonx1 gen() 594 MB/s
[ 2.322249] raid6: neonx1 xor() 626 MB/s
[ 2.492366] raid6: neonx2 gen() 986 MB/s
[ 2.662383] raid6: neonx2 xor() 948 MB/s
[ 2.832483] raid6: neonx4 gen() 1312 MB/s
[ 3.002539] raid6: neonx4 xor() 1172 MB/s
[ 3.172609] raid6: neonx8 gen() 1300 MB/s
[ 3.342693] raid6: neonx8 xor() 1131 MB/s
[ 3.346835] raid6: using algorithm neonx4 gen() 1312 MB/s
[ 3.352320] raid6: … xor() 1172 MB/s, rmw enabled
[ 3.357808] raid6: using neon recovery algorithm
[ 3.363376] SCSI subsystem initialized
[ 3.367402] usbcore: registered new interface driver usbfs
[ 3.372918] usbcore: registered new interface driver hub
[ 3.378267] usbcore: registered new device driver usb
[ 3.384006] pxa2xx-i2c d0011000.i2c: could not find pctldev for node /soc/internal-regs@d0000000/pinctrl@13800/i2c1-pins, deferring probe
[ 3.398027] clocksource: Switched to clocksource arch_sys_counter
[ 3.411895] NET: Registered protocol family 2
[ 3.416801] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.424006] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 3.430808] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.437553] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 3.443711] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 3.450112] NET: Registered protocol family 1
[ 3.454939] RPC: Registered named UNIX socket transport module.
[ 3.460734] RPC: Registered udp transport module.
[ 3.465562] RPC: Registered tcp transport module.
[ 3.470805] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.477588] Unpacking initramfs…
[ 3.502002] Freeing initrd memory: 5888K
[ 3.506665] Crashlog allocated RAM at address 0x3f00000
[ 3.512515] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 3.523459] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.530086] NFS: Registering the id_resolver key type
[ 3.535242] Key type id_resolver registered
[ 3.539392] Key type id_legacy registered
[ 3.543799] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.556022] io scheduler noop registered
[ 3.559773] io scheduler deadline registered (default)
[ 3.668409] OF: PCI: host bridge /soc/pcie@d0070000 ranges:
[ 3.673928] OF: PCI: MEM 0xe8000000…0xe8ffffff → 0xe8000000
[ 3.680305] OF: PCI: IO 0xe9000000…0xe900ffff → 0xe9000000
[ 4.177848] advk-pcie d0070000.pcie: link up
[ 4.182408] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
[ 4.188820] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.194559] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xe8ffffff]
[ 4.201231] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xe9000000-0xe900ffff])
[ 4.211514] pci 0000:00:00.0: enabling Extended Tags
[ 4.216625] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.224646] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x100000
[ 4.232936] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x108000
[ 4.240847] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x110000
[ 4.249309] pci 0000:01:03.0: enabling Extended Tags
[ 4.254651] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x120000
[ 4.262765] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x128000
[ 4.270428] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x130000
[ 4.279157] pci 0000:01:07.0: enabling Extended Tags
[ 4.284223] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x140000
[ 4.292218] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x148000
[ 4.300308] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x150000
[ 4.308584] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x158000
[ 4.316688] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x160000
[ 4.324798] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x168000
[ 4.332640] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x170000
[ 4.340823] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x178000
[ 4.348916] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x180000
[ 4.357181] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x188000
[ 4.365291] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x190000
[ 4.373042] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x198000
[ 4.381492] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1a0000
[ 4.389602] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1a8000
[ 4.397706] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1b0000
[ 4.405816] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1b8000
[ 4.413567] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1c0000
[ 4.421928] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1c8000
[ 4.430110] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1d0000
[ 4.437766] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1d8000
[ 4.446225] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1e0000
[ 4.454405] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1e8000
[ 4.462426] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1f0000
[ 4.470608] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x1f8000
[ 4.478629] pci 0000:01:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.486641] pci 0000:01:07.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.496017] advk-pcie d0070000.pcie: Posted PIO Response Status: UR, 0xc80 @ 0x300000
[ 4.503896] pci 0000:00:00.0: BAR 8: assigned [mem 0xe8000000-0xe82fffff]
[ 4.510785] pci 0000:01:03.0: BAR 8: assigned [mem 0xe8000000-0xe82fffff]
[ 4.518156] pci 0000:02:00.0: BAR 0: assigned [mem 0xe8000000-0xe81fffff 64bit]
[ 4.525750] pci 0000:02:00.0: BAR 6: assigned [mem 0xe8200000-0xe820ffff pref]
[ 4.533228] pci 0000:01:03.0: PCI bridge to [bus 02]
[ 4.538291] pci 0000:01:03.0: bridge window [mem 0xe8000000-0xe82fffff]
[ 4.545398] pci 0000:01:07.0: PCI bridge to [bus 03]
[ 4.550390] pci 0000:00:00.0: PCI bridge to [bus 01-03]
[ 4.555667] pci 0000:00:00.0: bridge window [mem 0xe8000000-0xe82fffff]
[ 4.564281] mv_xor d0060900.xor: Marvell shared XOR driver
[ 4.628451] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 4.698425] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 4.706565] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 4.715100] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 4.725390] loop: module loaded
[ 4.734419] random: fast init done
[ 4.743200] m25p80 spi0.0: w25q64dw (8192 Kbytes)
[ 4.748116] 5 fixed-partitions partitions found on MTD device spi0.0
[ 4.754688] Creating 5 MTD partitions on “spi0.0”:
[ 4.759213] 0x000000000000-0x000000020000 : “secure-firmware”
[ 4.765793] 0x000000020000-0x000000180000 : “u-boot”
[ 4.771242] 0x000000180000-0x000000190000 : “u-boot-env”
[ 4.777188] 0x000000190000-0x0000007f0000 : “Rescue system”
[ 4.783497] 0x0000007f0000-0x000000800000 : “dtb”
[ 4.788971] moxtet spi0.1: Found SD Turris Mox CPU module
[ 4.794472] moxtet spi0.1: Unknown Moxtet module found (ID 0x06)
[ 4.800706] moxtet spi0.1: Peridot Switch module found
[ 4.806435] libphy: Fixed MDIO Bus: probed
[ 4.811377] libphy: orion_mdio_bus: probed
[ 4.816329] mv88e6085 d0032004.mdio-mii:10: switch 0x1900 detected: Marvell 88E6190, revision 1
[ 4.841071] libphy: /soc/internal-regs@d0000000/mdio@32004/switch0@10/mdio: probed
[ 4.877512] mvneta d0030000.ethernet eth0: Using device tree mac address d8:58:d7:00:b4:5e
[ 4.887121] mvneta d0040000.ethernet eth1: Using device tree mac address d8:58:d7:00:b4:5f
[ 4.895812] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 4.902409] ehci-pci: EHCI PCI platform driver
[ 4.907038] ehci-platform: EHCI generic platform driver
[ 4.912322] ehci-orion: EHCI orion driver
[ 4.916859] orion-ehci d005e000.usb: EHCI Host Controller
[ 4.922294] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
[ 4.930106] orion-ehci d005e000.usb: irq 13, io mem 0xd005e000
[ 4.957862] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
[ 4.964361] hub 1-0:1.0: USB hub found
[ 4.967948] hub 1-0:1.0: 1 port detected
[ 4.973167] usbcore: registered new interface driver usb-storage
[ 4.979415] i2c /dev entries driver
[ 4.983804] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec, nowayout
[ 4.991687] sdhci: Secure Digital Host Controller Interface driver
[ 4.997727] sdhci: Copyright(c) Pierre Ossman
[ 5.002364] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.008512] xenon-sdhci d00d0000.sdhci: allocated mmc-pwrseq
[ 5.014558] xenon-sdhci d00d8000.sdhci: Got CD GPIO
[ 5.022864] NET: Registered protocol family 10
[ 5.028256] Segment Routing with IPv6
[ 5.031827] NET: Registered protocol family 17
[ 5.036485] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 5.050220] 8021q: 802.1Q VLAN Support v1.8
[ 5.054127] Key type dns_resolver registered
[ 5.059058] registered taskstats version 1
[ 5.064702] Btrfs loaded, crc32c=crc32c-generic
[ 5.073674] rtc-ds1307 0-006f: registered as rtc0
[ 5.078635] i2c i2c-0: PXA I2C adapter
[ 5.082799] mv88e6085 d0032004.mdio-mii:10: switch 0x1900 detected: Marvell 88E6190, revision 1
[ 5.104867] libphy: /soc/internal-regs@d0000000/mdio@32004/switch0@10/mdio: probed
[ 5.131408] DSA: switch 0 0 parsed
[ 5.134848] DSA: tree 0 parsed
[ 5.337855] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 5.538808] hub 1-1:1.0: USB hub found
[ 5.542452] hub 1-1:1.0: 2 ports detected
[ 5.999793] mv88e6085 d0032004.mdio-mii:10 lan1 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:01] driver [Marvell 88E6390]
[ 6.119795] mv88e6085 d0032004.mdio-mii:10 lan2 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:02] driver [Marvell 88E6390]
[ 6.229796] mv88e6085 d0032004.mdio-mii:10 lan3 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:03] driver [Marvell 88E6390]
[ 6.349795] mv88e6085 d0032004.mdio-mii:10 lan4 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:04] driver [Marvell 88E6390]
[ 6.459795] mv88e6085 d0032004.mdio-mii:10 lan5 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:05] driver [Marvell 88E6390]
[ 6.569795] mv88e6085 d0032004.mdio-mii:10 lan6 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:06] driver [Marvell 88E6390]
[ 6.679797] mv88e6085 d0032004.mdio-mii:10 lan7 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:07] driver [Marvell 88E6390]
[ 6.799795] mv88e6085 d0032004.mdio-mii:10 lan8 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@10!mdio:08] driver [Marvell 88E6390]
[ 6.817384] xhci-hcd d0058000.usb: xHCI Host Controller
[ 6.822843] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
[ 6.830187] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010010
[ 6.839631] xhci-hcd d0058000.usb: irq 12, io mem 0xd0058000
[ 6.845961] hub 2-0:1.0: USB hub found
[ 6.849533] hub 2-0:1.0: 1 port detected
[ 6.853643] xhci-hcd d0058000.usb: xHCI Host Controller
[ 6.859036] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
[ 6.866843] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
[ 6.873553] usb usb3: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 6.882201] hub 3-0:1.0: USB hub found
[ 6.885834] hub 3-0:1.0: 1 port detected
[ 6.890723] xenon-sdhci d00d0000.sdhci: allocated mmc-pwrseq
[ 6.957858] mmc0: SDHCI controller on d00d0000.sdhci [d00d0000.sdhci] using ADMA
[ 6.965863] xenon-sdhci d00d8000.sdhci: Got CD GPIO
[ 7.011104] sdio_read_cccr card report SDIO_UHS_DDR50
[ 7.016065] sdio_read_cccr card report SDIO_UHS_SDR50
[ 7.021292] sdio_read_cccr card report SDIO_UHS_SDR104
[ 7.028039] mmc1: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
[ 7.042349] armada-37xx-rwtm-mailbox d00b0000.mailbox: Trust Status: 00000000
[ 7.173410] Turris Mox serial number 0000000D300006CF
[ 7.178468] board version 22
[ 7.182230] burned RAM size 1024 MiB
[ 7.368738] xenon-sdhci d00d0000.sdhci: Timing issue might occur in DDR mode
[ 7.512384] random: crng init done
[ 7.515926] rtc-ds1307 0-006f: setting system clock to 2021-02-21 11:57:11 UTC (1613908631)
[ 7.695240] Freeing unused kernel memory: 320K
[ 7.705242] mmc0: new ultra high speed DDR50 SDIO card at address 0001
Starting network boot!
Initializing the system
udhcpc: started, v1.29.3
Setting IP address 0.0.0.0 on eth0
[ 7.938443] mvneta d0030000.ethernet eth0: PHY [d0032004.mdio-mii:01] driver [Marvell 88E1510]
[ 7.947707] mvneta d0030000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 7.958518] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc: sending discover
udhcpc: sending discover
[ 12.219072] mvneta d0030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.227601] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
udhcpc: sending discover
udhcpc: sending select for 192.168.2.101
udhcpc: lease of 192.168.2.101 obtained, lease time 43200
Setting IP address 192.168.2.101 on eth0
Deleting routers
route: SIOCDELRT: No such process
Adding router 192.168.2.1
Recreating /etc/resolv.conf
Adding DNS server 192.168.2.1
Pseudo-terminal will not be allocated because stdin is not a terminal.
ash: /usr/bin/netboot-server: not found
tar: invalid magic
tar: short read
Can’t get rootfs
[ 14.868024] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000100
[ 14.868024]
[ 14.877589] SMP: stopping secondary CPUs
[ 14.881693] Kernel Offset: disabled
[ 14.885428] CPU features: 0x0802008
[ 14.889103] Memory Limit: none
[ 14.897798] Rebooting in 1 seconds…
