My turris 1.1 is kernel panicking right after start after update 
U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
CPU0: P2020E, Version: 2.1, (0x80ea0021)
Core: e500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:1200 MHz, CPU1:1200 MHz,
CCB:600 MHz,
DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
wdt status 00000005 reset
Watchdog enabled
Board: TURRIS CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
in: 56
out: 0
io_config: 255
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C: Error, wrong i2c adapter 2 max 2 possible
ready
SPI: ready
DRAM: Error, wrong i2c adapter 2 max 2 possible
Detected UDIMM 9905594-009.A00LF
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2: 512 KiB enabled
NAND: 256 MiB
MMC: FSL_SDHC: 0
PCIe1: Root Complex of mini PCIe SLOT, x1 gen1, regs @ 0xffe0a000
01:00.0 - 168c:003c - Network controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
03:00.0 - 168c:0030 - Network controller
PCIe2: Bus 02 - 03
PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
05:00.0 - 104c:8241 - Serial bus controller
PCIe3: Bus 04 - 05
Error, wrong i2c adapter 2 max 2 possible
In: serial
Out: serial
Err: serial
Net: Phy 5 not found
PHY reset timed out
eTSEC1
Error: eTSEC1 address not set.
, eTSEC2
Error: eTSEC2 address not set.
, eTSEC3 [PRIME]
Error: eTSEC3 address not set.
Hit any key to stop autoboot: 1 0
BOOT NAND
reading zImage
5929661 bytes read in 262 ms (21.6 MiB/s)
wdt status 00000003
reading fdt
13731 bytes read in 13 ms (1 MiB/s)
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02100000 ...
Image Name: Linux-5.15.147
Created: 2024-02-02 1:42:18 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 5929597 Bytes = 5.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ff9000, end 03fff5a2 ... OK
WARNING: could not find compatible node fsl-usb2-dr
[ 0.000000] Memory CAM mapping: 256/256/256 Mb, residual: 1280Mb
[ 0.000000] Linux version 5.15.147 (packaging@turris.cz) (powerpc-openwrt-linux-muslspe-gcc (OpenWrt GCC 8.4.0 r16881+135-4a1d8ef55c) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Fri Feb 2 01:42:18 2024
[ 0.000000] Using P2020RDB-PC machine description
[ 0.000000] printk: bootconsole [udbg0] enabled
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] -----------------------------------------------------
[ 0.000000] phys_mem_size = 0x80000000
[ 0.000000] dcache_bsize = 0x20
[ 0.000000] icache_bsize = 0x20
[ 0.000000] cpu_features = 0x0000000010010108
[ 0.000000] possible = 0x0000000010010108
[ 0.000000] always = 0x0000000010010108
[ 0.000000] cpu_user_features = 0x84e08000 0x08000000
[ 0.000000] mmu_features = 0x00020010
[ 0.000000] -----------------------------------------------------
mpc85xx_rdb_setup_arch()
[ 0.000000] ioremap() called early from of_iomap+0x48/0x80. Use early_ioremap() instead
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
[ 0.000000] barrier-nospec: using isync; sync as speculation barrier
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] percpu: Embedded 11 pages/cpu s13868 r8192 d22996 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait rw rootfstype=btrfs rootflags=subvol=@,commit=5 console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xffbbf000..0xfffff000 : fixmap
[ 0.000000] * 0xff400000..0xff800000 : highmem PTEs
[ 0.000000] * 0xff3fe000..0xff400000 : early ioremap
[ 0.000000] * 0xf1000000..0xff3fe000 : vmalloc & ioremap
[ 0.000000] Memory: 1998976K/2097152K available (9544K kernel code, 728K rwdata, 1996K rodata, 256K init, 276K bss, 98176K reserved, 0K cma-reserved, 1310712K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000005] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x114c1bade8, max_idle_ns: 440795203839 ns
[ 0.010295] clocksource: timebase mult[d555555] shift[24] registered
[ 0.016765] Console: colour dummy device 80x25
[ 0.021149] pid_max: default: 32768 minimum: 301
[ 0.025840] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.033094] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.041504] mpic: requesting IPIs...
[ 0.045676] e500 family performance monitor hardware support registered
[ 0.052305] rcu: Hierarchical SRCU implementation.
[ 0.057169] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.064873] smp: Bringing up secondary CPUs ...
[ 0.069950] smp: Brought up 1 node, 2 CPUs
[ 0.074395] devtmpfs: initialized
[ 0.079662] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.089433] futex hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.096986] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.103417] thermal_sys: Registered thermal governor 'step_wise'
[ 0.111085] Machine: Turris 1.x
[ 0.120139] SoC family: QorIQ
[ 0.123093] SoC ID: svr:0x80ea0021, Revision: 2.1
[ 0.129156] Found FSL PCI host bridge at 0x00000000ffe08000. Firmware bus number: 0->1
[ 0.136993] PCI host bridge /pcie@ffe08000 (primary) ranges:
[ 0.142661] MEM 0x00000000c0000000..0x00000000c01fffff -> 0x00000000c0000000
[ 0.149861] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.157011] /pcie@ffe08000: PCICSRBAR @ 0xfff00000
[ 0.161769] setup_pci_atmu: end of DRAM 80000000
[ 0.166748] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1
[ 0.174595] PCI host bridge /pcie@ffe09000 ranges:
[ 0.179460] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.186690] IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
[ 0.193811] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.198587] setup_pci_atmu: end of DRAM 80000000
[ 0.203547] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->1
[ 0.211393] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.216259] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[ 0.223477] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[ 0.230608] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.235385] setup_pci_atmu: end of DRAM 80000000
[ 0.241038] software IO TLB: tearing down default memory pool
[ 0.253549] PCI: Probing PCI hardware
[ 0.257262] fsl-pci ffe08000.pcie: PCI host bridge to bus 0002:00
[ 0.263277] pci_bus 0002:00: root bus resource [io 0x0000-0xffff]
[ 0.269463] pci_bus 0002:00: root bus resource [mem 0xc0000000-0xc01fffff]
[ 0.276317] pci_bus 0002:00: root bus resource [bus 00-ff]
[ 0.281801] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff
[ 0.288426] pci 0002:00:00.0: [1957:0070] type 01 class 0x060400
[ 0.294414] pci 0002:00:00.0: reg 0x10: [mem 0xfff00000-0xffffffff]
[ 0.300700] pci 0002:00:00.0: supports D1 D2
[ 0.304925] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.312599] pci 0002:01:00.0: [104c:8241] type 00 class 0x0c0330
[ 0.318552] pci 0002:01:00.0: reg 0x10: [mem 0xc0000000-0xc000ffff 64bit]
[ 0.325315] pci 0002:01:00.0: reg 0x18: [mem 0xc0010000-0xc0011fff 64bit]
[ 0.332187] pci 0002:01:00.0: supports D1 D2
[ 0.336371] pci 0002:01:00.0: PME# supported from D0 D1 D2 D3hot
[ 0.342407] pci 0002:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0002:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 0.388090] pci 0002:00:00.0: PCI bridge to [bus 01-ff]
[ 0.393235] pci 0002:00:00.0: bridge window [io 0x0000-0x0fff]
[ 0.399332] pci 0002:00:00.0: bridge window [mem 0xc0000000-0xc00fffff]
[ 0.406106] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.412717] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.419434] fsl-pci ffe09000.pcie: PCI host bridge to bus 0001:02
[ 0.425456] pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff])
[ 0.434398] pci_bus 0001:02: root bus resource [mem 0xa0000000-0xbfffffff]
[ 0.441273] pci_bus 0001:02: root bus resource [bus 02-ff]
[ 0.446743] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to ff
[ 0.453373] pci 0001:02:00.0: [1957:0070] type 01 class 0x060400
[ 0.459353] pci 0001:02:00.0: reg 0x10: [mem 0xfff00000-0xffffffff]
[ 0.465655] pci 0001:02:00.0: supports D1 D2
[ 0.469867] pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.477413] pci 0001:02:00.0: Primary bus is hard wired to 0
[ 0.482989] pci 0001:02:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
[ 0.491080] pci 0001:03:00.0: [168c:0030] type 00 class 0x028000
[ 0.497021] pci 0001:03:00.0: reg 0x10: [mem 0xa0000000-0xa001ffff 64bit]
[ 0.503826] pci 0001:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.510547] pci 0001:03:00.0: supports D1
[ 0.514487] pci 0001:03:00.0: PME# supported from D0 D1 D3hot
[ 0.545317] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.550462] pci 0001:02:00.0: bridge window [io 0x20000-0x20fff]
[ 0.556733] pci 0001:02:00.0: bridge window [mem 0xa0000000-0xa00fffff]
[ 0.563507] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03
[ 0.570118] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 03
[ 0.576818] fsl-pci ffe0a000.pcie: PCI host bridge to bus 0000:04
[ 0.582840] pci_bus 0000:04: root bus resource [io 0x40000-0x4ffff] (bus address [0x0000-0xffff])
[ 0.591782] pci_bus 0000:04: root bus resource [mem 0x80000000-0x9fffffff]
[ 0.598658] pci_bus 0000:04: root bus resource [bus 04-ff]
[ 0.604127] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to ff
[ 0.610758] pci 0000:04:00.0: [1957:0070] type 01 class 0x060400
[ 0.616737] pci 0000:04:00.0: reg 0x10: [mem 0xfff00000-0xffffffff]
[ 0.623038] pci 0000:04:00.0: supports D1 D2
[ 0.627251] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.634800] pci 0000:04:00.0: Primary bus is hard wired to 0
[ 0.640376] pci 0000:04:00.0: bridge configuration invalid ([bus 01-01]), reconfiguring
[ 0.648467] pci 0000:05:00.0: [168c:003c] type 00 class 0x028000
[ 0.654408] pci 0000:05:00.0: reg 0x10: [mem 0x80000000-0x801fffff 64bit]
[ 0.661212] pci 0000:05:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.667933] pci 0000:05:00.0: supports D1 D2
[ 0.702970] pci 0000:04:00.0: PCI bridge to [bus 05-ff]
[ 0.708115] pci 0000:04:00.0: bridge window [io 0x40000-0x40fff]
[ 0.714386] pci 0000:04:00.0: bridge window [mem 0x80000000-0x801fffff]
[ 0.721160] pci_bus 0000:05: busn_res: [bus 05-ff] end is updated to 05
[ 0.727771] pci_bus 0000:04: busn_res: [bus 04-ff] end is updated to 05
[ 0.734427] PCI: Cannot allocate resource region 0 of device 0002:00:00.0, will remap
[ 0.742204] PCI: Cannot allocate resource region 0 of device 0001:02:00.0, will remap
[ 0.750019] PCI: Cannot allocate resource region 0 of device 0000:04:00.0, will remap
[ 0.757891] pci 0002:00:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.764446] pci 0002:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.771412] pci 0002:00:00.0: PCI bridge to [bus 01]
[ 0.776357] pci 0002:00:00.0: bridge window [io 0x0000-0xffff]
[ 0.782456] pci 0002:00:00.0: bridge window [mem 0xc0000000-0xc01fffff]
[ 0.789224] pci_bus 0002:00: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.798272] pci_bus 0002:00: resource 4 [io 0x0000-0xffff]
[ 0.803827] pci_bus 0002:00: resource 5 [mem 0xc0000000-0xc01fffff]
[ 0.810093] pci_bus 0002:01: resource 0 [io 0x0000-0xffff]
[ 0.815650] pci_bus 0002:01: resource 1 [mem 0xc0000000-0xc01fffff]
[ 0.821920] pci 0001:02:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.828516] pci 0001:02:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.835482] pci 0001:03:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
[ 0.842687] pci 0001:02:00.0: PCI bridge to [bus 03]
[ 0.847650] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff]
[ 0.853901] pci 0001:02:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.860695] pci_bus 0001:02: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.869723] pci_bus 0001:02: resource 4 [io 0x20000-0x2ffff]
[ 0.875468] pci_bus 0001:02: resource 5 [mem 0xa0000000-0xbfffffff]
[ 0.881719] pci_bus 0001:03: resource 0 [io 0x20000-0x2ffff]
[ 0.887463] pci_bus 0001:03: resource 1 [mem 0xa0000000-0xbfffffff]
[ 0.893720] pci 0000:04:00.0: BAR 0: no space for [mem size 0x00100000]
[ 0.900330] pci 0000:04:00.0: BAR 0: failed to assign [mem size 0x00100000]
[ 0.907280] pci 0000:05:00.0: BAR 6: assigned [mem 0x80200000-0x8020ffff pref]
[ 0.914501] pci 0000:04:00.0: PCI bridge to [bus 05]
[ 0.919449] pci 0000:04:00.0: bridge window [io 0x40000-0x4ffff]
[ 0.925716] pci 0000:04:00.0: bridge window [mem 0x80000000-0x9fffffff]
[ 0.932489] pci_bus 0000:04: Some PCI device resources are unassigned, try booting with pci=realloc
[ 0.941542] pci_bus 0000:04: resource 4 [io 0x40000-0x4ffff]
[ 0.947267] pci_bus 0000:04: resource 5 [mem 0x80000000-0x9fffffff]
[ 0.953534] pci_bus 0000:05: resource 0 [io 0x40000-0x4ffff]
[ 0.959263] pci_bus 0000:05: resource 1 [mem 0x80000000-0x9fffffff]
[ 0.973146] raid6: skip pq benchmark and using algorithm int32x8
[ 0.979113] raid6: using intx1 recovery algorithm
[ 0.984179] SCSI subsystem initialized
[ 0.987963] usbcore: registered new interface driver usbfs
[ 0.993410] usbcore: registered new interface driver hub
[ 0.998689] usbcore: registered new device driver usb
[ 1.003777] EDAC MC: Ver: 3.0.0
[ 1.007878] clocksource: Switched to clocksource timebase
[ 1.018315] NET: Registered PF_INET protocol family
[ 1.023279] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 1.031428] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 1.039727] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.047444] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 1.055233] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.062398] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.068751] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.075311] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 1.082485] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.088126] pci 0002:00:00.0: enabling device (0106 -> 0107)
[ 1.093809] PCI: CLS 32 bytes, default 32
[ 1.098588] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 1.107922] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.113752] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZO) (LZMA) (RTIME) (RUBIN) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.125765] xor: measuring software checksum speed
[ 1.136758] 8regs : 1574 MB/sec
[ 1.148855] 8regs_prefetch : 1258 MB/sec
[ 1.159381] 32regs : 1573 MB/sec
[ 1.170720] 32regs_prefetch : 1391 MB/sec
[ 1.174988] xor: using function: 8regs (1574 MB/sec)
[ 1.180017] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.188650] pcieport 0002:00:00.0: AER: enabled with IRQ 24
[ 1.194305] pcieport 0001:02:00.0: enabling device (0106 -> 0107)
[ 1.200777] pcieport 0001:02:00.0: AER: enabled with IRQ 25
[ 1.206423] pcieport 0000:04:00.0: enabling device (0106 -> 0107)
[ 1.212767] pcieport 0000:04:00.0: AER: enabled with IRQ 26
[ 1.218638] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.227707] printk: console [ttyS0] disabled
\CA+HH\90\901.231958] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 37500000) is a 16550A
[ 1.240607] printk: console [ttyS0] enabled
[ 1.240607] printk: console [ttyS0] enabled
[ 1.248932] printk: bootconsole [udbg0] disabled
[ 1.248932] printk: bootconsole [udbg0] disabled
[ 1.258481] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550A
[ 1.267762] printk: console [ttyS0] disabled
[ 1.272153] printk: console [ttyS0] enabled
[ 1.276779] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 37500000) is a 16550
[ 1.286341] Loading iSCSI transport class v2.0-870.
[ 1.293567] physmap-flash ef000000.nor: physmap platform flash device: [mem 0xef000000-0xefffffff]
[ 1.302751] ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 1.312782] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.317965] Amd/Fujitsu Extended Query version 1.3.
[ 1.323020] number of CFI chips: 1
[ 1.326809] 7 fixed-partitions partitions found on MTD device ef000000.nor
[ 1.333713] Creating 7 MTD partitions on "ef000000.nor":
[ 1.339039] 0x000000000000-0x000000020000 : "dtb"
[ 1.344267] 0x000000020000-0x0000001c0000 : "kernel"
[ 1.349675] 0x0000001c0000-0x000000340000 : "rescue"
[ 1.355036] 0x000000340000-0x000000e40000 : "factory"
[ 1.360545] 0x000000e40000-0x000000f00000 : "certificates"
[ 1.366427] 0x000000f20000-0x000000f40000 : "u-boot-env"
[ 1.372191] 0x000000f40000-0x000001000000 : "u-boot"
[ 1.380124] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.386495] nand: Micron MT29F2G08ABAEAWP
[ 1.390523] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.399269] Bad block table found at page 131008, version 0x01
[ 1.406011] Bad block table found at page 130944, version 0x01
[ 1.412615] 1 fixed-partitions partitions found on MTD device ff800000.flash
[ 1.419690] Creating 1 MTD partitions on "ff800000.flash":
[ 1.425180] 0x000000000000-0x000010000000 : "rootfs"
[ 1.431347] mtd: setting mtd7 (rootfs) as root device
[ 1.436773] mtdsplit: no squashfs found in "rootfs"
[ 1.441961] eLBC NAND device at 0xff800000, bank 1
[ 1.447399] fsl_espi ffe07000.spi: irq = 59
[ 1.458273] fsl-gianfar ffe24000.ethernet: Using random MAC address: a6:02:bc:28:5d:4d
[ 1.466537] fsl-gianfar ffe24000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.484446] fsl-gianfar ffe24000.ethernet eth0: mac: a6:02:bc:28:5d:4d
[ 1.491016] fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled
[ 1.497811] fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256
[ 1.504963] fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256
[ 1.512286] fsl-gianfar ffe25000.ethernet: Using random MAC address: 52:62:e5:fe:38:7f
[ 1.520551] fsl-gianfar ffe25000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.538445] fsl-gianfar ffe25000.ethernet eth1: mac: 52:62:e5:fe:38:7f
[ 1.544990] fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled
[ 1.551794] fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256
[ 1.558942] fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256
[ 1.566260] fsl-gianfar ffe26000.ethernet: Using random MAC address: a6:d7:e7:78:99:c3
[ 1.574208] fsl-gianfar ffe26000.ethernet: enabled errata workarounds, flags: 0x4
[ 1.592041] fsl-gianfar ffe26000.ethernet eth2: mac: a6:d7:e7:78:99:c3
[ 1.598592] fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled
[ 1.605384] fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256
[ 1.612530] fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256
[ 1.619846] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[ 1.625857] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.632472] ehci-pci: EHCI PCI platform driver
[ 1.637285] fsl-ehci: Freescale EHCI Host controller driver
[ 1.642937] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.649583] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.656866] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 1.697877] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.704001] hub 1-0:1.0: USB hub found
[ 1.707794] hub 1-0:1.0: 1 port detected
[ 1.712314] usbcore: registered new interface driver uas
[ 1.717713] usbcore: registered new interface driver usb-storage
[ 1.723956] i2c_dev: i2c /dev entries driver
[ 1.728404] mpc-i2c ffe03000.i2c: timeout 1000000 us
[ 1.733628] i2c i2c-0: of_i2c: modalias failure on /soc@ffe00000/i2c@3000/power-control@2a
[ 1.741939] i2c i2c-0: Failed to create I2C device for /soc@ffe00000/i2c@3000/power-control@2a
[ 1.750601] i2c i2c-0: of_i2c: modalias failure on /soc@ffe00000/i2c@3000/eeprom@32
[ 1.758281] i2c i2c-0: Failed to create I2C device for /soc@ffe00000/i2c@3000/eeprom@32
[ 1.766470] i2c i2c-0: of_i2c: modalias failure on /soc@ffe00000/i2c@3000/eeprom@57
[ 1.774155] i2c i2c-0: Failed to create I2C device for /soc@ffe00000/i2c@3000/eeprom@57
[ 1.782645] mpc-i2c ffe03100.i2c: timeout 1000000 us
[ 1.788145] booke_wdt: powerpc book-e watchdog driver loaded
[ 1.794041] Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software
[ 1.801168] fsl_mc_err_probe: No ECC DIMMs discovered
[ 1.806769] EDAC DEVICE0: Giving out device to module MPC85xx_edac controller mpc85xx_l2_err: DEV mpc85xx_l2_err (INTERRUPT)
[ 1.818118] MPC85xx_edac acquired irq 16 for L2 Err
[ 1.822997] MPC85xx_edac L2 err registered
[ 1.827423] EDAC PCI0: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.0.auto (INTERRUPT)
[ 1.839300] MPC85xx_edac acquired irq 24 for PCI Err
[ 1.844265] MPC85xx_edac PCI err registered
[ 1.848523] EDAC PCI1: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.1.auto (INTERRUPT)
[ 1.860389] MPC85xx_edac acquired irq 25 for PCI Err
[ 1.865354] MPC85xx_edac PCI err registered
[ 1.869609] EDAC PCI2: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.2.auto (INTERRUPT)
[ 1.881481] MPC85xx_edac acquired irq 26 for PCI Err
[ 1.886446] MPC85xx_edac PCI err registered
[ 1.890923] sdhci: Secure Digital Host Controller Interface driver
[ 1.897113] sdhci: Copyright(c) Pierre Ossman
[ 1.901484] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.907423] sdhci-esdhc ffe2e000.sdhc: Got CD GPIO
[ 1.907782] NET: Registered PF_INET6 protocol family
[ 1.912316] mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
[ 1.918460] Segment Routing with IPv6
[ 1.928439] In-situ OAM (IOAM) with IPv6
[ 1.932420] NET: Registered PF_PACKET protocol family
[ 1.937527] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.948031] mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA
[ 1.950703] 8021q: 802.1Q VLAN Support v1.8
[ 1.961948] drmem: No dynamic reconfiguration memory found
[ 1.970218] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[ 2.042636] mmc0: new high speed SDHC card at address 59b4
[ 2.048298] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 2.055182] mmcblk0: mmc0:59b4 SD 7.36 GiB
[ 2.065812] mmcblk0: p1 p2
[ 2.084071] device eth1 entered promiscuous mode
[ 2.088850] device eth0 entered promiscuous mode
[ 2.097998] qca8k mdio@ffe24520:10: configuring for fixed/rgmii-id link mode
[ 2.110066] qca8k mdio@ffe24520:10: configuring for fixed/rgmii-id link mode
[ 2.119819] qca8k mdio@ffe24520:10: Link is Up - 1Gbps/Full - flow control off
[ 2.128399] qca8k mdio@ffe24520:10: Link is Up - 1Gbps/Full - flow control off
[ 2.201182] qca8k mdio@ffe24520:10 lan5 (uninitialized): PHY [qca8k-0.0:01] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.291210] qca8k mdio@ffe24520:10 lan4 (uninitialized): PHY [qca8k-0.0:02] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.298733] hub 1-1:1.0: USB hub found
[ 2.306879] hub 1-1:1.0: 2 ports detected
[ 2.381192] qca8k mdio@ffe24520:10 lan3 (uninitialized): PHY [qca8k-0.0:03] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.471185] qca8k mdio@ffe24520:10 lan2 (uninitialized): PHY [qca8k-0.0:04] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.561184] qca8k mdio@ffe24520:10 lan1 (uninitialized): PHY [qca8k-0.0:05] driver [Qualcomm Atheros 8337 internal PHY] (irq=POLL)
[ 2.573450] DSA: tree 0 setup
[ 2.583109] BTRFS: device fsid 102f5ee7-4016-4565-9718-be41bd28e459 devid 1 transid 1087963 /dev/root scanned by swapper/0 (1)
[ 2.606274] BTRFS info (device mmcblk0p2): using crc32c (crc32c-generic) checksum algorithm
[ 2.614729] BTRFS info (device mmcblk0p2): disk space caching is enabled
[ 2.621453] BTRFS info (device mmcblk0p2): has skinny extents
[ 2.739180] BTRFS info (device mmcblk0p2): enabling ssd optimizations
[ 2.801530] VFS: Mounted root (btrfs filesystem) on device 0:14.
[ 2.814178] devtmpfs: mounted
[ 2.817416] Freeing unused kernel image (initmem) memory: 256K
[ 2.823279] This architecture does not have kernel memory protection.
[ 2.829744] Run /sbin/init as init process
[ 3.123557] init: Console is alive
[ 3.127084] init: - watchdog -
[ 4.805209] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.829368] pps_core: LinuxPPS API ver. 1 registered
[ 4.834349] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 4.844519] PTP clock support registered
[ 4.849178] Button Hotplug driver version 0.4.1
[ 4.854898] ehci-platform: EHCI generic platform driver
[ 4.872739] xhci_hcd 0002:01:00.0: xHCI Host Controller
[ 4.878055] xhci_hcd 0002:01:00.0: new USB bus registered, assigned bus number 2
[ 4.885611] xhci_hcd 0002:01:00.0: hcc params 0x0270f06d hci version 0x96 quirks 0x0000000004000000
[ 4.895073] xhci_hcd 0002:01:00.0: xHCI Host Controller
[ 4.900328] xhci_hcd 0002:01:00.0: new USB bus registered, assigned bus number 3
[ 4.907734] xhci_hcd 0002:01:00.0: Host supports USB 3.0 SuperSpeed
[ 4.914555] hub 2-0:1.0: USB hub found
[ 4.918386] hub 2-0:1.0: 4 ports detected
[ 4.922824] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.931418] hub 3-0:1.0: USB hub found
[ 4.935220] hub 3-0:1.0: 4 ports detected
[ 4.944551] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.953068] init: - preinit -
[ 5.207915] usb 2-1: new full-speed USB device number 2 using xhci_hcd
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.411730] random: procd: uninitialized urandom read (4 bytes read)
[ 7.333644] mount_root: mounting /dev/root
[ 7.827603] urandom-seed: Seeding with /etc/urandom.seed
Scanning for Btrfs filesystems
[ 8.644868] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead.
reg[ 9.241804] BTRFS info: devid 1 device path /dev/root changed to /dev/mmcblk0p2 scanned by btrfs (504)
istered: /dev/mmcblk0p2
[ 9.255005] procd: - early -
[ 9.257972] procd: - watchdog -
[ 9.829153] procd: - watchdog -
[ 9.839640] procd: - ubus -
[ 9.878036] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.892639] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.899220] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.907067] procd: - init -
Please press Enter to activate this console.
[ 11.418183] random: crng init done
[ 11.421597] random: 15 urandom warning(s) missed due to ratelimiting
[ 15.065516] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.197796] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 15.237591] pca953x 0-0018: supply vcc not found, using dummy regulator
[ 15.244451] pca953x 0-0018: using no AI
[ 15.252487] GACT probability on
[ 15.257316] Mirror/redirect action on
[ 15.266700] u32 classifier
[ 15.269489] input device check on
[ 15.273161] Actions configured
[ 15.285476] Bridge firewalling registered
[ 15.290706] Loading modules backported from Linux version v5.15.81-0-ge4a7232c917c
[ 15.298384] Backport generated by backports.git v5.15.81-1-0-ge1867d55
[ 15.314169] lm90 0-004c: supply vcc not found, using dummy regulator
[ 15.322122] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 15.328728] hwmon hwmon0: temp2_input not attached to any thermal zone
[ 15.339758] pps pps0: new PPS source ptp0
[ 15.350652] rtc-ds1307 0-006f: registered as rtc0
[ 15.356368] rtc-ds1307 0-006f: setting system clock to 2024-02-16T12:23:20 UTC (1708086200)
[ 15.366997] usbcore: registered new interface driver ums-alauda
[ 15.373397] usbcore: registered new interface driver ums-cypress
[ 15.379959] usbcore: registered new interface driver ums-datafab
[ 15.386407] usbcore: registered new interface driver ums-freecom
[ 15.392931] usbcore: registered new interface driver ums-isd200
[ 15.399344] usbcore: registered new interface driver ums-jumpshot
[ 15.405865] usbcore: registered new interface driver ums-karma
[ 15.412315] usbcore: registered new interface driver ums-sddr09
[ 15.418840] usbcore: registered new interface driver ums-sddr55
[ 15.425287] usbcore: registered new interface driver ums-usbat
[ 15.438148] xt_time: kernel timezone is -0000
[ 15.504186] PPP generic driver version 2.4.2
[ 15.509225] NET: Registered PF_PPPOX protocol family
[ 15.535994] ath10k_pci 0000:05:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 15.960524] ath10k_pci 0000:05:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 15.969838] ath10k_pci 0000:05:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 15.979911] ath10k_pci 0000:05:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[ 16.110393] ath10k_pci 0000:05:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 17.250012] ath10k_pci 0000:05:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 17.550316] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xf2c20000, irq=37
[ 17.557349] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 21.959098] fsl-gianfar ffe25000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 21.967411] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 21.975648] qca8k mdio@ffe24520:10 lan1: configuring for phy/gmii link mode
[ 21.986331] br-guest: port 1(lan1.3) entered blocking state
[ 21.992010] br-guest: port 1(lan1.3) entered disabled state
[ 21.997835] device lan1.3 entered promiscuous mode
[ 22.002675] device lan1 entered promiscuous mode
[ 22.010510] qca8k mdio@ffe24520:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 22.023216] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 22.033503] br-lan: port 1(lan1) entered blocking state
[ 22.038820] br-lan: port 1(lan1) entered disabled state
[ 22.051865] br-guest: port 1(lan1.3) entered blocking state
[ 22.057465] br-guest: port 1(lan1.3) entered forwarding state
[ 22.070256] br-lan: port 1(lan1) entered blocking state
[ 22.075514] br-lan: port 1(lan1) entered forwarding state
[ 22.081280] IPv6: ADDRCONF(NETDEV_CHANGE): br-guest: link becomes ready
[ 22.100339] qca8k mdio@ffe24520:10 lan2: configuring for phy/gmii link mode
[ 22.109801] qca8k mdio@ffe24520:10 lan2: Link is Up - 100Mbps/Full - flow control rx/tx
[ 22.125034] br-lan: port 2(lan2) entered blocking state
[ 22.130371] br-lan: port 2(lan2) entered disabled state
[ 22.136958] device lan2 entered promiscuous mode
[ 22.153702] br-lan: port 2(lan2) entered blocking state
[ 22.158980] br-lan: port 2(lan2) entered forwarding state
[ 22.174584] qca8k mdio@ffe24520:10 lan3: configuring for phy/gmii link mode
[ 22.188026] br-lan: port 3(lan3) entered blocking state
[ 22.193272] br-lan: port 3(lan3) entered disabled state
[ 22.199694] device lan3 entered promiscuous mode
[ 22.214135] qca8k mdio@ffe24520:10 lan4: configuring for phy/gmii link mode
[ 22.226400] br-lan: port 4(lan4) entered blocking state
[ 22.231682] br-lan: port 4(lan4) entered disabled state
[ 22.253822] device lan4 entered promiscuous mode
[ 22.270575] qca8k mdio@ffe24520:10 lan5: configuring for phy/gmii link mode
[ 22.280366] br-lan: port 5(lan5) entered blocking state
[ 22.285609] br-lan: port 5(lan5) entered disabled state
[ 22.303092] device lan5 entered promiscuous mode
[ 23.080020] ath: EEPROM regdomain: 0x80cb
[ 23.084042] ath: EEPROM indicates we should expect a country code
[ 23.090195] ath: doing EEPROM country->regdmn map search
[ 23.095520] ath: country maps to regdmn code: 0x37
[ 23.100348] ath: Country alpha2 being used: CZ
[ 23.104823] ath: Regpair used: 0x37
[ 23.108348] ath: regdomain 0x80cb dynamically updated by user
[ 23.114189] ath: EEPROM regdomain: 0x80cb
[ 23.118244] ath: EEPROM indicates we should expect a country code
[ 23.124361] ath: doing EEPROM country->regdmn map search
[ 23.129685] ath: country maps to regdmn code: 0x37
[ 23.134494] ath: Country alpha2 being used: CZ
[ 23.138970] ath: Regpair used: 0x37
[ 23.142460] ath: regdomain 0x80cb dynamically updated by user
[ 23.811796] br-lan: port 6(wlan1) entered blocking state
[ 23.817160] br-lan: port 6(wlan1) entered disabled state
[ 23.822758] device wlan1 entered promiscuous mode
[ 23.827564] br-lan: port 6(wlan1) entered blocking state
[ 23.832898] br-lan: port 6(wlan1) entered forwarding state
[ 23.942117] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 24.110462] br-guest: port 2(wlan1-1) entered blocking state
[ 24.116146] br-guest: port 2(wlan1-1) entered disabled state
[ 24.122154] device wlan1-1 entered promiscuous mode
[ 24.138252] br-guest: port 2(wlan1-1) entered blocking state
[ 24.143942] br-guest: port 2(wlan1-1) entered forwarding state
[ 24.155590] br-guest: port 2(wlan1-1) entered disabled state
[ 24.308805] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready
[ 24.315510] br-guest: port 2(wlan1-1) entered blocking state
[ 24.321209] br-guest: port 2(wlan1-1) entered forwarding state
[ 26.551304] ath10k_pci 0000:05:00.0: pdev param 0 not supported by firmware
[ 26.574813] br-lan: port 7(wlan0) entered blocking state
[ 26.580223] br-lan: port 7(wlan0) entered disabled state
[ 26.585785] device wlan0 entered promiscuous mode
[ 26.590646] br-lan: port 7(wlan0) entered blocking state
[ 26.595985] br-lan: port 7(wlan0) entered forwarding state
[ 26.606286] br-lan: port 7(wlan0) entered disabled state
Router Turris successfully started.
[ 41.591357] BUG: scheduling while atomic: foris-notify/4148/0x00000100
[ 41.597912] Modules linked in: ath9k ath9k_common xt_connlimit pppoe ppp_async nf_conncount iptable_nat ath9k_hw ath10k_pci ath10k_core ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat_ftp nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack_ftp nf_conntrack mt7915e mt76_connac_lib mt76 mac80211 ipt_REJECT ebtable_nat ebtable_filter ebtable_broute cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_recent xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_comment xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda slhc sch_cake rtc_ds1307 ptp_qoriq nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 lm90 iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables hwmon ebtables ebt_vlan ebt_stp ebt_redirect ebt_pkttype ebt_mark_m ebt_mark ebt_limit ebt_among
[ 41.598256] ebt_802_3 crc_ccitt compat br_netfilter sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact configs gpio_pca953x regmap_i2c xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb sit ip6_tunnel netlink_diag tunnel6 tunnel4 ip_tunnel nls_utf8 sha256_ppc_spe seqiv jitterentropy_rng drbg md5_ppc hmac cmac gpio_keys leds_turris_1x leds_gpio xhci_plat_hcd xhci_pci xhci_hcd ahci libahci libata ehci_platform button_hotplug ptp pps_core
[ 41.762205] CPU: 0 PID: 4148 Comm: foris-notify Not tainted 5.15.147 #0
[ 41.768837] Call Trace:
[ 41.771277] [efff3d90] [c050dab0] dump_stack_lvl+0x4c/0x6c (unreliable)
[ 41.777911] [efff3db0] [c0062cf0] __schedule_bug+0x54/0x6c
[ 41.783402] [efff3dc0] [c094b67c] __schedule+0x3b4/0x5e4
[ 41.788727] [efff3e10] [c094b910] schedule+0x64/0xe0
[ 41.793696] [efff3e30] [c094bc54] schedule_preempt_disabled+0x10/0x20
[ 41.800144] [efff3e40] [c094d5b4] __mutex_lock.isra.14+0x480/0x49c
[ 41.806331] [efff3e90] [f1132664] 0xf1132664
[ 41.810606] [efff3ec0] [c070a18c] led_timer_function+0x98/0x1cc
[ 41.816533] [efff3ee0] [c00afec4] call_timer_fn.isra.35+0x24/0x84
[ 41.822634] [efff3f00] [c00b0220] run_timer_softirq+0x2fc/0x388
[ 41.828559] [efff3f90] [c0951df0] __do_softirq+0x150/0x298
[ 41.834049] [efff3ff0] [c00053d0] do_softirq_own_stack+0x34/0x4c
[ 41.840065] [c8003ed0] [c000a774] timer_interrupt+0x1c8/0x2b0
[ 41.845821] [c8003ef0] [c003e7a4] irq_exit+0x88/0xc4
[ 41.850798] [c8003f10] [c000138c] Decrementer+0x14c/0x160
[ 41.856201] --- interrupt: 900 at 0xb7a5ac90
[ 41.860470] NIP: b7a5ac90 LR: b7a5ab4c CTR: b79e8280
[ 41.865519] REGS: c8003f20 TRAP: 0900 Not tainted (5.15.147)
[ 41.871439] MSR: 0202d000 <VEC,CE,EE,PR,ME> CR: 44002484 XER: 00000000
[ 41.878249]
[ 41.878249] GPR00: b7a5aa38 bf97ada0 b7d3d18c 00000000 00000009 13efd169 bf97adb8 0126dd88
[ 41.878249] GPR08: b7c84460 2f69c95e 2f69c95e bf97ada0 44002888 00000000 00000000 b7d31010
[ 41.878249] GPR16: b7c81720 01238514 00b00c18 012f6b08 bf97aef8 0139072c 01399128 01390744
[ 41.878249] GPR24: 01399128 13efd169 0129db00 012386a0 012f6b08 00000018 b7c6637c 013993a8
[ 41.913220] NIP [b7a5ac90] 0xb7a5ac90
[ 41.916880] LR [b7a5ab4c] 0xb7a5ab4c
[ 41.920452] --- interrupt: 900
[ 41.931684] Oops: Exception in kernel mode, sig: 4 [#1]
[ 41.936931] BE PAGE_SIZE=4K SMP NR_CPUS=2 P2020RDB-PC
[ 41.941985] Modules linked in: ath9k ath9k_common xt_connlimit pppoe ppp_async nf_conncount iptable_nat ath9k_hw ath10k_pci ath10k_core ath xt_state xt_nat xt_helper xt_conntrack xt_connmark xt_connbytes xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT pppox ppp_generic nf_nat_ftp nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack_ftp nf_conntrack mt7915e mt76_connac_lib mt76 mac80211 ipt_REJECT ebtable_nat ebtable_filter ebtable_broute cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_recent xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_comment xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda slhc sch_cake rtc_ds1307 ptp_qoriq nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 lm90 iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables hwmon ebtables ebt_vlan ebt_stp ebt_redirect ebt_pkttype ebt_mark_m ebt_mark ebt_limit ebt_among
[ 41.942300] ebt_802_3 crc_ccitt compat br_netfilter sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact configs gpio_pca953x regmap_i2c xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb sit ip6_tunnel netlink_diag tunnel6 tunnel4 ip_tunnel nls_utf8 sha256_ppc_spe seqiv jitterentropy_rng drbg md5_ppc hmac cmac gpio_keys leds_turris_1x leds_gpio xhci_plat_hcd xhci_pci xhci_hcd ahci libahci libata ehci_platform button_hotplug ptp pps_core
[ 42.106177] CPU: 1 PID: 4148 Comm: foris-notify Tainted: G W 5.15.147 #0
[ 42.114189] NIP: efff3d80 LR: efff3d80 CTR: c006dcec
[ 42.119239] REGS: efff3ce0 TRAP: 0700 Tainted: G W (5.15.147)
[ 42.126552] MSR: 02021000 <VEC,CE,ME> CR: c24f72a0 XER: 00000000
[ 42.132834]
[ 42.132834] GPR00: c24f72a0 efff3dc0 c22e6040 c2478000 efff3d80 c2c39f20 00000000 00000001
[ 42.132834] GPR08: 00021000 0000003c 82004424 b73b4030 22004242 c0c2816c efff3e84 efff3e1c
[ 42.132834] GPR16: efff3dc0 c00769e4 00000000 c29e2054 efff3d50 000001c6 000001c6 00001c94
[ 42.132834] GPR24: efff3d80 eedc9c00 0002c580 c11cbe20 efff3d60 c00de8e8 00000000 c29af0f8
[ 42.167804] NIP [efff3d80] 0xefff3d80
[ 42.171466] LR [efff3d80] 0xefff3d80
[ 42.175039] Call Trace:
[ 42.177480] Instruction dump:
[ 42.180446] XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
[ 42.188208] XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
[ 42.195972] ---[ end trace 0a70bdfadba7ca55 ]---
[ 42.200587]
[ 43.202084] Kernel panic - not syncing: Fatal exception
[ 43.207313] Rebooting in 3 seconds..
U-Boot 2015.04-04654-gbcfb33e-dirty (Jun 26 2015 - 12:50:49)
CPU0: P2020E, Version: 2.1, (0x80ea0021)
Core: e500, Version: 5.1, (0x80211051)
Clock Configuration:
CPU0:1200 MHz, CPU1:1200 MHz,
CCB:600 MHz,
DDR:400 MHz (800 MT/s data rate) (Asynchronous), LBC:37.500 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
wdt status 00000005 reset
Watchdog enabled
Board: TURRIS CPLD: V4.1 PCBA: V4.0
Error, wrong i2c adapter 2 max 2 possible
in: 200
out: 0
io_config: 255
rom_loc: nor upper bank
SD/MMC : 4-bit Mode
eSPI : Enabled
I2C: Error, wrong i2c adapter 2 max 2 possible
ready
SPI: ready
DRAM: Error, wrong i2c adapter 2 max 2 possible
Detected UDIMM 9905594-009.A00LF
WARNING: Calling __hwconfig without a buffer and before environment is ready
WARNING: Calling __hwconfig without a buffer and before environment is ready
2 GiB (DDR3, 64-bit, CL=6, ECC off)
Flash: 16 MiB
L2: 512 KiB enabled
NAND: 256 MiB
MMC: FSL_SDHC: 0
PCIe1: Root Complex of mini PCIe SLOT, x1 gen1, regs @ 0xffe0a000
01:00.0 - 168c:003c - Network controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe09000
03:00.0 - 168c:0030 - Network controller
PCIe2: Bus 02 - 03
PCIe3: Root Complex of PCIe SLOT, x1 gen1, regs @ 0xffe08000
05:00.0 - 104c:8241 - Serial bus controller
PCIe3: Bus 04 - 05
Error, wrong i2c adapter 2 max 2 possible
In: serial
Out: serial
Err: serial
Net: Phy 5 not found
PHY reset timed out
eTSEC1
Error: eTSEC1 address not set.
, eTSEC2
Error: eTSEC2 address not set.
, eTSEC3 [PRIME]
Error: eTSEC3 address not set.
Hit any key to stop autoboot: 1 0
BOOT NAND
reading zImage
5929661 bytes read in 263 ms (21.5 MiB/s)
wdt status 00000003
reading fdt
13731 bytes read in 13 ms (1 MiB/s)
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02100000 ...
Image Name: Linux-5.15.147
Created: 2024-02-02 1:42:18 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 5929597 Bytes = 5.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Uncompressing Kernel Image ... OK
Loading Device Tree to 03ff9000, end 03fff5a2 ... OK
WARNING: could not find compatible node fsl-usb2-dr
[ 0.000000] Memory CAM mapping: 256/256/256 Mb, residual: 1280Mb
[ 0.000000] Linux version 5.15.147 (packaging@turris.cz) (powerpc-openwrt-linux-muslspe-gcc (OpenWrt GCC 8.4.0 r16881+135-4a1d8ef55c) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Fri Feb 2 01:42:18 2024
[ 0.000000] Using P2020RDB-PC machine description
[ 0.000000] printk: bootconsole [udbg0] enabled
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] -----------------------------------------------------
[ 0.000000] phys_mem_size = 0x80000000
[ 0.000000] dcache_bsize = 0x20
[ 0.000000] icache_bsize = 0x20
[ 0.000000] cpu_features = 0x0000000010010108
[ 0.000000] possible = 0x0000000010010108
[ 0.000000] always = 0x0000000010010108
[ 0.000000] cpu_user_features = 0x84e08000 0x08000000
[ 0.000000] mmu_features = 0x00020010
[ 0.000000] -----------------------------------------------------
mpc85xx_rdb_setup_arch()
[ 0.000000] ioremap() called early from of_iomap+0x48/0x80. Use early_ioremap() instead
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
[ 0.000000] barrier-nospec: using isync; sync as speculation barrier
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] percpu: Embedded 11 pages/cpu s13868 r8192 d22996 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rootwait rw rootfstype=btrfs rootflags=subvol=@,commit=5 console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Updates
Bug Fixes