It worked, it has booted and is running now 
I donāt know what version of U-Boot I ran before my upgrade, probably a very old one.
U-Boot after the upgrade to 6.5.0 and firmware upgrade was:
U-Boot 2022.10-rc4-OpenWrt-r16653+119-44ce70f0e2 (Sep 15 2022 - 18:21:35 +0000)
now, when on 7.0 and after your instructions:
U-Boot 2024.01-OpenWrt-r20293+119-4432454037 (Mar 07 2024 - 04:53:41 +0000), Build: jenkins-TurrisOS-packages-hbl-omnia-768
I will monitor and report any crashes here.
@DIKKEHENK the problem is not with swap, the problem can manifest itself in various ways, if my suspicion is correct. Basically, a memtest would fail because the DDR controller is incorrectly configured.
@tuomaz please let us know if this helps. If it does help, I will send the patches to upstream U-Boot and we can finally upgrade U-Boot for everyone. This problem was chasing us for several years.
ah ok. And how do i do a mem test to check if i have the same problem?
Since i do suspect something is wonky on the WAN part after the whole FW update circus, but canāt put my nOOby finger on it?
Sadly, it has rebooted 3 times since yesterday. Below is the serial console log for the last crash + boot.
Router Turris successfully started.
[17051.167777] 8<--- cut here ---
[17051.170850] Unable to handle kernel paging request at virtual address 57035a10
[17051.178088] pgd = b5d5a519
[17051.180802] [57035a10] *pgd=00000000
[17051.184389] Internal error: Oops: 80000005 [#1] SMP ARM
[17051.189627] Modules linked in: ath9k ath9k_common qcserial pppoe ppp_async iptable_nat ath9k_hw ath10k_pci ath10k_core ath xt_state xt_nat xt_conntrack xt_REDIRECT xt_MASQUERADE xt_FLOWOFFLOAD xt_CT usb_wwan pppox ppp_generic nft_redir nft_ct nf_nat_ftp nf_nat nf_flow_table nf_conntrack_netlink nf_conntrack_ftp nf_conntrack mt7915e mt76_connac_lib mt76 mac80211 ipt_REJECT ebtable_nat ebtable_filter ebtable_broute cfg80211 xt_time xt_tcpudp xt_tcpmss xt_statistic xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_ecn xt_dscp xt_comment xt_TCPMSS xt_LOG xt_HL xt_DSCP xt_CLASSIFY usbserial ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda slhc sch_cake nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_quota nft_objref nft_numgen nft_log nft_limit nft_hash nft_counter nft_compat nf_tables nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 iptable_mangle iptable_filter ipt_ECN ip_tables ebtables ebt_vlan
[17051.189805] ebt_stp ebt_redirect ebt_pkttype ebt_mark_m ebt_mark ebt_limit ebt_among ebt_802_3 crc_ccitt compat br_netfilter at24 sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact configs i2c_mux_pca954x i2c_mux ledtrig_oneshot ledtrig_gpio xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 ifb sit sctp udp_tunnel ip6_udp_tunnel ip6_tunnel netlink_diag tunnel6 tunnel4 ip_tunnel nls_utf8 seqiv jitterentropy_rng drbg md5 hmac ghash_arm_ce cmac uas leds_turris_omnia turris_omnia_mcu ledtrig_transient ahci fsl_mph_dr_of ehci_fsl
[17051.362154] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.148 #0
[17051.368264] Hardware name: Marvell Armada 380/385 (Device Tree)
[17051.374196] PC is at 0x57035a10
[17051.377345] LR is at 0x57035a10
[17051.380492] pc : [<57035a10>] lr : [<57035a10>] psr: 20000193
[17051.386772] sp : c1083e50 ip : c1082000 fp : 00000f82
[17051.392007] r10: 20000193 r9 : eeddcd54 r8 : c1083f60
[17051.397242] r7 : 57035a10 r6 : 00000f82 r5 : c0f03d00 r4 : eeddcfa8
[17051.403784] r3 : 0000000a r2 : 00198fee r1 : 00000f82 r0 : c00000be
[17051.410326] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
[17051.417566] Control: 10c5387d Table: 03fcc04a DAC: 00000051
[17051.423323] Register r0 information: non-slab/vmalloc memory
[17051.428998] Register r1 information: non-paged memory
[17051.434062] Register r2 information: non-paged memory
[17051.439124] Register r3 information: non-paged memory
[17051.444186] Register r4 information: non-slab/vmalloc memory
[17051.449858] Register r5 information: non-slab/vmalloc memory
[17051.455529] Register r6 information: non-paged memory
[17051.460592] Register r7 information: non-paged memory
[17051.465654] Register r8 information: non-slab/vmalloc memory
[17051.471325] Register r9 information: non-slab/vmalloc memory
[17051.476997] Register r10 information: non-paged memory
[17051.482147] Register r11 information: non-paged memory
[17051.487295] Register r12 information: non-slab/vmalloc memory
[17051.493054] Process swapper/1 (pid: 0, stack limit = 0xe270b608)
[17051.499074] Stack: (0xc1083e50 to 0xc1084000)
[17051.503442] 3e40: c1083f60 c01ae150 20000113 cfdbbc6b
[17051.511640] 3e60: c10d65c0 eeddcfa8 eeddcd40 eeddcd00 c01ae0b0 eeddcd00 eeddcd54 c019d174
[17051.519838] 3e80: c10d65c0 57035696 00000000 57035696 00000f82 c0f75800 00000001 eeddcd00
[17051.528036] 3ea0: 57035696 00000f82 20000193 eeddcd0c eeddcd88 eeddcdb0 eeddcdd8 c019daf0
[17051.536233] 3ec0: 20000193 0000000f 00000003 eeddce50 eeddce30 eeddce80 57035696 00000f82
[17051.544431] 3ee0: c0e56224 00000001 c10147c0 c0f05404 0000001a c0e57cd4 f080210c c1083f40
[17051.552627] 3f00: c1083fb8 c010df94 c1010400 c018484c c0e57cc8 00000000 0000001d 00000000
[17051.560824] 3f20: c0e57cd4 c017e760 c0f05404 c1083f60 c0f85a30 f0802100 c0e57cd4 c01012e4
[17051.569021] 3f40: c01076d4 60000013 ffffffff c1083f94 00000000 c1082000 00000000 c0100b7c
[17051.577218] 3f60: 010ad636 00000000 00000001 c0117c20 c1082000 c0f04f54 00000001 c0f04f98
[17051.585414] 3f80: 00000000 c0e580a8 00000000 c1083fb8 c3e2a03c c1083fb0 c01076d0 c01076d4
[17051.593612] 3fa0: 60000013 ffffffff 00000051 c0190768 c1082000 c015f540 10c0387d c0f105d4
[17051.601809] 3fc0: 00000051 cfdbbc6b c1083ff8 00000098 00000051 10c0387d c1083ff8 0000406a
[17051.610007] 3fe0: 414fc091 00000000 00000000 c015f8e0 010d806a 00101770 00000000 00000000
[17051.618204] Code: bad PC value
[17051.621264] ---[ end trace 7936ceb606d82802 ]---
[17051.625892] Kernel panic - not syncing: Fatal exception in interrupt
[17051.632262] CPU0: stopping
[17051.634979] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 5.15.148 #0
[17051.642482] Hardware name: Marvell Armada 380/385 (Device Tree)
[17051.648417] [<c010e9b0>] (unwind_backtrace) from [<c010a69c>] (show_stack+0x10/0x14)
[17051.656187] [<c010a69c>] (show_stack) from [<c05f3f1c>] (dump_stack_lvl+0x40/0x4c)
[17051.663779] [<c05f3f1c>] (dump_stack_lvl) from [<c010cbc4>] (do_handle_IPI+0xf8/0x12c)
[17051.671716] [<c010cbc4>] (do_handle_IPI) from [<c010cc10>] (ipi_handler+0x18/0x20)
[17051.679304] [<c010cc10>] (ipi_handler) from [<c018484c>] (handle_percpu_devid_irq+0x78/0x13c)
[17051.687853] [<c018484c>] (handle_percpu_devid_irq) from [<c017e760>] (handle_domain_irq+0x5c/0x78)
[17051.696839] [<c017e760>] (handle_domain_irq) from [<c01012e4>] (gic_handle_irq+0x7c/0x90)
[17051.705041] [<c01012e4>] (gic_handle_irq) from [<c0100b7c>] (__irq_svc+0x5c/0x78)
[17051.712543] Exception stack(0xc0f01f10 to 0xc0f01f58)
[17051.717606] 1f00: 0123ffd0 00000000 00000001 c0117c20
[17051.725803] 1f20: c0f00000 c0f04f54 00000000 c0f04f98 00000000 c0e580a8 00000000 c0f01f68
[17051.733999] 1f40: c107c03c c0f01f60 c01076d0 c01076d4 60000013 ffffffff
[17051.740627] [<c0100b7c>] (__irq_svc) from [<c01076d4>] (arch_cpu_idle+0x38/0x3c)
[17051.748047] [<c01076d4>] (arch_cpu_idle) from [<c015f540>] (do_idle+0x1ec/0x258)
[17051.755467] [<c015f540>] (do_idle) from [<c015f8e0>] (cpu_startup_entry+0x18/0x1c)
[17051.763057] [<c015f8e0>] (cpu_startup_entry) from [<c0e0124c>] (start_kernel+0x72c/0x768)
[17051.771265] Rebooting in 3 seconds..
BootROM - 1.73
Booting from SPI flash
U-Boot SPL 2024.01-OpenWrt-r20293+119-4432454037 (Mar 07 2024 - 04:53:41 +0000)
High speed PHY - Version: 2.0
MiniPCIe/mSATA card detection... mSATA
WWAN slot configuration... PCIe+USB2.0
Detected Device ID 6820
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 6 | SATA0 |
| 1 | 5 | USB3 HOST0 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
--------------------------------
High speed PHY - Ended Successfully
Using old DDR3 training implementation
DDR3 Training Sequence - Ver TIP-1.29.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Trying to boot from SPI
U-Boot 2024.01-OpenWrt-r20293+119-4432454037 (Mar 07 2024 - 04:53:41 +0000), Build: jenkins-TurrisOS-packages-hbl-omnia-768
SoC: MV88F6820-A0 at 1600 MHz
DRAM: 2 GiB (800 MHz, 32-bit, 2T, ECC not enabled)
Core: 84 devices, 28 uclasses, devicetree: separate
WDT: Started watchdog@20300 with servicing every 1000ms (60s timeout)
MMC: mv_sdh: 0
Loading Environment from SPIFlash... SF: Detected s25fl164k with page size 256 Bytes, erase size 4 KiB, total 8 MiB
OK
Model: Turris Omnia
MCU type: STM32
MCU version: b5a8a24e007eb72be16aeb3fff6f03ec647023e4/67eddc9540526d0a9d9660f7a7867af9a28a68d6
RAM size: 2048 MiB
Board version: unknown
Serial Number: 0000000B0000EC80
Disabling MCU watchdog... disabled
Regdomain set to **
pcie1.0: Link down
pcie2.0: Link down
Net: eth0: ethernet@70000, eth1: ethernet@30000, eth2: ethernet@34000 [PRIME], eth3: lan0, eth4: lan1, eth5: lan2, eth6: lan3, eth7: lan4
Hit any key to stop autoboot: 3 2 1 0
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
1199 bytes read in 80 ms (13.7 KiB/s)
## Executing script at 01800000
gpio: pin gpio@71_4 (gpio 52) value is 1
21434 bytes read in 97 ms (214.8 KiB/s)
4285824 bytes read in 345 ms (11.8 MiB/s)
Kernel image @ 0x1000000 [ 0x000000 - 0x416580 ]
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Working FDT set to 2000000
Loading Device Tree to 0fff7000, end 0ffff3b9 ... OK
Working FDT set to fff7000
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.148 (packaging@turris.cz) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r20293+119-4432454037) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Mar 7 04:53:41 2024
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Turris Omnia
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14988 r8192 d21876 u45056
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: earlyprintk rootwait console=ttyS0,115200 rootfstype=btrfs root=PARTUUID=a1df57b5-01 rootflags=commit=5,subvol=@ rw cfg80211.freg=**
[ 0.000000] Bootloader command line not present
[ 0.000000] Unknown kernel command line parameters "earlyprintk mangled_fs=btrfs", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2062464K/2097152K available (10240K kernel code, 672K rwdata, 2192K rodata, 1024K init, 258K bss, 34688K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Registering MPIC SoC Error Interrupt Controller
[ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000001] sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000017] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
[ 0.000034] Switching to timer-based delay loop, resolution 1ns
[ 0.000172] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000178] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000361] Console: colour dummy device 80x30
[ 0.000388] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=8000000)
[ 0.000397] CPU: Testing write buffer coherency: ok
[ 0.000416] CPU0: Spectre v2: using BPIALL workaround
[ 0.000421] pid_max: default: 32768 minimum: 301
[ 0.000507] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000515] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000986] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001294] Setting up static identity map for 0x100000 - 0x100060
[ 0.001376] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.001462] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001523] rcu: Hierarchical SRCU implementation.
[ 0.001602] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.001666] smp: Bringing up secondary CPUs ...
[ 0.001834] Booting CPU 1
[ 0.001966] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001972] CPU1: Spectre v2: using BPIALL workaround
[ 0.002028] smp: Brought up 1 node, 2 CPUs
[ 0.002035] SMP: Total of 2 processors activated (3200.00 BogoMIPS).
[ 0.002040] CPU: All CPU(s) started in SVC mode.
[ 0.002392] devtmpfs: initialized
[ 0.004311] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.004364] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.004374] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.004448] pinctrl core: initialized pinctrl subsystem
[ 0.004993] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.005507] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.005967] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006111] cpuidle: using governor ladder
[ 0.006202] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.006209] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.006331] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.006338] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.014732] cryptd: max_cpu_qlen set to 1000
[ 0.015555] raid6: skip pq benchmark and using algorithm neonx8
[ 0.015564] raid6: using neon recovery algorithm
[ 0.015826] SCSI subsystem initialized
[ 0.015997] usbcore: registered new interface driver usbfs
[ 0.016020] usbcore: registered new interface driver hub
[ 0.016038] usbcore: registered new device driver usb
[ 0.016653] clocksource: Switched to clocksource arm_global_timer
[ 0.018909] NET: Registered PF_INET protocol family
[ 0.019017] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.019517] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.019534] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.019543] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.019581] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.019643] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.019691] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.019722] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.019825] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.019843] PCI: CLS 0 bytes, default 64
[ 0.020337] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 0.022267] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.024251] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.024258] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.024683] xor: measuring software checksum speed
[ 0.028518] arm4regs : 2598 MB/sec
[ 0.033640] 8regs : 1922 MB/sec
[ 0.038775] 32regs : 1917 MB/sec
[ 0.043800] neon : 1958 MB/sec
[ 0.043803] xor: using function: arm4regs (2598 MB/sec)
[ 0.043847] bounce: pool size: 64 pages
[ 0.043876] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.044966] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.045506] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 0.045802] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 0.046124] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges:
[ 0.046153] mvebu-pcie soc:pcie: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 0.046171] mvebu-pcie soc:pcie: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.046184] mvebu-pcie soc:pcie: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 0.046196] mvebu-pcie soc:pcie: MEM 0x00f1048000..0x00f1049fff -> 0x0000048000
[ 0.046208] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.046220] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.046232] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.046243] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.046254] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.046266] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.046277] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.046285] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.046374] mvebu-pcie soc:pcie: pcie1.0: Slot power limit 10.0W
[ 0.046427] mvebu-pcie soc:pcie: pcie2.0: Slot power limit 10.0W
[ 0.047293] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 0.047306] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.047315] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 0.047323] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.047330] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 0.047341] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff])
[ 0.047347] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.047352] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.047448] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[ 0.047607] pci 0000:00:03.0: [11ab:6820] type 01 class 0x060400
[ 0.048440] PCI: bus0: Fast back to back transfers disabled
[ 0.048448] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.048459] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.049292] PCI: bus1: Fast back to back transfers enabled
[ 0.049299] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.050134] PCI: bus2: Fast back to back transfers enabled
[ 0.050141] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.050163] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe03fffff]
[ 0.050172] pci 0000:00:03.0: BAR 8: assigned [mem 0xe0400000-0xe07fffff]
[ 0.050179] pci 0000:00:02.0: BAR 7: assigned [io 0x10000-0x10fff]
[ 0.050185] pci 0000:00:03.0: BAR 7: assigned [io 0x20000-0x20fff]
[ 0.050192] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 0.050197] pci 0000:00:02.0: bridge window [io 0x10000-0x10fff]
[ 0.050208] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe03fffff]
[ 0.050219] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 0.050224] pci 0000:00:03.0: bridge window [io 0x20000-0x20fff]
[ 0.050233] pci 0000:00:03.0: bridge window [mem 0xe0400000-0xe07fffff]
[ 0.050300] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[ 0.050361] pcieport 0000:00:02.0: pciehp: Slot #2 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ IbPresDis- LLActRep+
[ 0.050564] pcieport 0000:00:02.0: pciehp: Slot(2): Card present
[ 0.050639] pcieport 0000:00:03.0: enabling device (0140 -> 0143)
[ 0.050695] pcieport 0000:00:03.0: pciehp: Slot #3 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ IbPresDis- LLActRep+
[ 0.051038] pcieport 0000:00:03.0: pciehp: Slot(3): Card present
[ 0.051301] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.107049] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.107206] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.167032] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.167304] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.168438] printk: console [ttyS0] disabled
[ 0.188543] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 15625000) is a 16550A
[ 1.286113] printk: console [ttyS0] enabled
[ 1.310800] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 31, base_baud = 15625000) is a 16550A
[ 1.322084] loop: module loaded
[ 1.325242] Loading iSCSI transport class v2.0-870.
[ 1.331388] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 1.339070] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 1.346593] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 1.354432] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.363511] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.372843] scsi host0: ahci-mvebu
[ 1.376543] scsi host1: ahci-mvebu
[ 1.380056] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53
[ 1.388007] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53
[ 1.397000] spi-nor spi0.0: s25fl164k (8192 Kbytes)
[ 1.402012] 3 fixed-partitions partitions found on MTD device spi0.0
[ 1.408426] Creating 3 MTD partitions on "spi0.0":
[ 1.413230] 0x000000000000-0x0000000f0000 : "U-Boot"
[ 1.418490] 0x000000100000-0x000000800000 : "Rescue system"
[ 1.424285] 0x0000000f0000-0x000000100000 : "u-boot-env"
[ 1.432449] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 1.439594] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 1.466809] hwmon hwmon1: temp1_input not attached to any thermal zone
[ 1.487341] hwmon hwmon2: temp1_input not attached to any thermal zone
[ 1.507315] hwmon hwmon3: temp1_input not attached to any thermal zone
[ 1.527311] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 1.547343] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 1.707668] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 1.716716] mvneta f1070000.ethernet eth0: Using device tree mac address d8:58:d7:00:5b:10
[ 1.726266] mvneta f1030000.ethernet eth1: Using device tree mac address d8:58:d7:00:5b:0e
[ 1.728179] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.740461] mvneta f1034000.ethernet eth2: Using device tree mac address d8:58:d7:00:5b:0f
[ 1.748890] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.755437] ehci-pci: EHCI PCI platform driver
[ 1.759925] ehci-platform: EHCI generic platform driver
[ 1.765243] ehci-orion: EHCI orion driver
[ 1.769362] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.774785] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.782424] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000
[ 1.816664] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.822909] hub 1-0:1.0: USB hub found
[ 1.826725] hub 1-0:1.0: 1 port detected
[ 1.831109] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.836450] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 1.844013] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 1.853292] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000
[ 1.859128] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.864458] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 1.872002] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.878634] hub 2-0:1.0: USB hub found
[ 1.882409] hub 2-0:1.0: 1 port detected
[ 1.886480] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.894815] hub 3-0:1.0: USB hub found
[ 1.898605] hub 3-0:1.0: 1 port detected
[ 1.902722] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.906682] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.908065] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.915165] ata1.00: ATA-9: SAMSUNG MZMTD128HAFV-000, DXT41K0Q, max UDMA/133
[ 1.921810] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 1.928818] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 32)
[ 1.938093] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000
[ 1.944738] ata1.00: Features: Dev-Sleep
[ 1.950437] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.954603] ata1.00: configured for UDMA/133
[ 1.959641] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.971612] scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZMTD128 1K0Q PQ: 0 ANSI: 5
[ 1.979766] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.986532] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 1.994173] sd 0:0:0:0: [sda] Write Protect is off
[ 1.999127] hub 4-0:1.0: USB hub found
[ 2.002899] hub 4-0:1.0: 1 port detected
[ 2.006694] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.007013] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.017139] sda: sda1 sda2
[ 2.027007] hub 5-0:1.0: USB hub found
[ 2.027365] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 2.030947] hub 5-0:1.0: 1 port detected
[ 2.040471] usbcore: registered new interface driver usb-storage
[ 2.047024] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 2.052594] armada38x-rtc f10a3800.rtc: setting system clock to 2024-03-10T19:09:26 UTC (1710097766)
[ 2.061918] i2c_dev: i2c /dev entries driver
[ 2.068450] orion_wdt: Initial timeout 171 sec
[ 2.073153] sdhci: Secure Digital Host Controller Interface driver
[ 2.079371] sdhci: Copyright(c) Pierre Ossman
[ 2.083841] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.090449] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 2.098127] NET: Registered PF_INET6 protocol family
[ 2.103800] Segment Routing with IPv6
[ 2.107507] In-situ OAM (IOAM) with IPv6
[ 2.111476] NET: Registered PF_PACKET protocol family
[ 2.115763] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 2.116566] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.137184] 8021q: 802.1Q VLAN Support v1.8
[ 2.141467] Registering SWP/SWPB emulation handler
[ 2.148536] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[ 2.156455] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 2.181481] hwmon hwmon2: temp1_input not attached to any thermal zone
[ 2.200682] hwmon hwmon3: temp1_input not attached to any thermal zone
[ 2.221480] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 2.230700] mmc0: new high speed MMC card at address 0001
[ 2.236429] mmcblk0: mmc0:0001 H8G4aļæ½ 7.28 GiB
[ 2.241814] mmcblk0: p1
[ 2.244739] mmcblk0boot0: mmc0:0001 H8G4aļæ½ 4.00 MiB
[ 2.250170] mmcblk0boot1: mmc0:0001 H8G4aļæ½ 4.00 MiB
[ 2.255581] mmcblk0rpmb: mmc0:0001 H8G4aļæ½ 4.00 MiB, chardev (247:0)
[ 2.262185] hwmon hwmon5: temp1_input not attached to any thermal zone
[ 2.285766] hwmon hwmon6: temp1_input not attached to any thermal zone
[ 2.292374] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.337666] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 2.343962] scsi host2: usb-storage 3-1:1.0
[ 3.136653] pcieport 0000:00:02.0: pciehp: Slot(2): No link
[ 3.212573] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 3.222477] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 3.231886] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 3.245156] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 3.340245] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-1:00] driver [Marvell 88E1540] (irq=76)
[ 3.366975] scsi 2:0:0:0: Direct-Access SanDisk Extreme 0001 PQ: 0 ANSI: 6
[ 3.445776] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-1:01] driver [Marvell 88E1540] (irq=77)
[ 3.486659] pcieport 0000:00:03.0: pciehp: Slot(3): No link
[ 3.560243] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-1:02] driver [Marvell 88E1540] (irq=78)
[ 3.571215] sd 2:0:0:0: [sdb] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
[ 3.579096] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.584201] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.595098] sdb: sdb1
[ 3.598302] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 3.675777] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-1:03] driver [Marvell 88E1540] (irq=79)
[ 3.800249] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-1:04] driver [Marvell 88E1540] (irq=80)
[ 3.817638] DSA: tree 0 setup
[ 3.822449] squashfs: Unknown parameter 'commit'
[ 3.827321] F2FS-fs (mmcblk0p1): Magic Mismatch, valid(0xf2f52010) - read(0x0)
[ 3.834564] F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock
[ 3.842420] F2FS-fs (mmcblk0p1): Magic Mismatch, valid(0xf2f52010) - read(0x0)
[ 3.849667] F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock
[ 3.857597] BTRFS: device fsid a3c67224-1247-453c-8a60-09adef987a62 devid 1 transid 128 /dev/root scanned by swapper/0 (1)
[ 3.869210] BTRFS info (device mmcblk0p1): using crc32c (crc32c-generic) checksum algorithm
[ 3.877639] BTRFS info (device mmcblk0p1): disk space caching is enabled
[ 3.884358] BTRFS info (device mmcblk0p1): has skinny extents
[ 3.900226] BTRFS info (device mmcblk0p1): enabling ssd optimizations
[ 3.910823] VFS: Mounted root (btrfs filesystem) on device 0:14.
[ 3.917592] devtmpfs: mounted
[ 3.921134] Freeing unused kernel image (initmem) memory: 1024K
[ 3.966819] Run /sbin/init as init process
[ 4.009585] init: Console is alive
[ 4.013096] init: - watchdog -
[ 4.229568] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.241411] fsl-ehci: Freescale EHCI Host controller driver
[ 4.250739] usbcore: registered new interface driver uas
[ 4.256232] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.273672] init: - preinit -
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.389134] mount_root: mounting /dev/root
Failed to find nls_cp437. Maybe it is a built in module ?
Failed to find nls_iso8859-1. Maybe it is a built in module ?
Failed to find fat. Maybe it is a built in module ?
Failed to find vfat. Maybe it is a built in module ?
[ 6.505818] BTRFS info: devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by mount (730)
[ 6.527871] urandom-seed: Seeding with /etc/urandom.seed
Scanning for Btrfs filesystems
registered: /dev[ 6.970506] BTRFS: device label srv devid 1 transid 2437 /dev/sda2 scanned by btrfs (737)
/sda2
registered: /dev/mmcblk0p1
[ 6.982556] procd: - early -
[ 6.985749] procd: - watchdog -
[ 7.522464] procd: - watchdog -
[ 7.525856] procd: - ubus -
[ 7.533696] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.578726] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.585218] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.592315] procd: - init -
Please press Enter to activate this console.
[ 7.765814] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.838798] sctp: Hash tables configured (bind 512/512)
[ 7.857726] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 7.919021] turris-omnia-mcu 1-002a: MCU type STM32
[ 7.926819] turris-omnia-mcu 1-002a: MCU bootloader firmware version hash: b5a8a24e007eb72be16aeb3fff6f03ec647023e4
[ 7.939960] turris-omnia-mcu 1-002a: MCU application firmware version hash: 67eddc9540526d0a9d9660f7a7867af9a28a68d6
[ 7.953996] turris-omnia-mcu 1-002a: registered as rtc1
[ 7.984866] i2c i2c-0: Added multiplexed i2c bus 1
[ 7.990033] i2c i2c-0: Added multiplexed i2c bus 2
[ 7.995177] i2c i2c-0: Added multiplexed i2c bus 3
[ 8.000472] i2c i2c-0: Added multiplexed i2c bus 4
[ 8.005612] i2c i2c-0: Added multiplexed i2c bus 5
[ 8.010862] i2c i2c-0: Added multiplexed i2c bus 6
[ 8.015991] i2c i2c-0: Added multiplexed i2c bus 7
[ 8.021647] pca953x 8-0071: supply vcc not found, using dummy regulator
[ 8.028402] pca953x 8-0071: using no AI
[ 8.034368] i2c i2c-0: Added multiplexed i2c bus 8
[ 8.039222] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547
[ 8.049162] GACT probability on
[ 8.053098] Mirror/redirect action on
[ 8.060346] u32 classifier
[ 8.063069] input device check on
[ 8.066775] Actions configured
[ 8.076828] at24 1-0054: supply vcc not found, using dummy regulator
[ 8.084335] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
[ 8.092149] Bridge firewalling registered
[ 8.094822] random: crng init done
[ 8.099626] random: 21 urandom warning(s) missed due to ratelimiting
[ 8.100737] Loading modules backported from Linux version v5.15.148-0-g6139f2a02fe0
[ 8.113700] Backport generated by backports.git v5.15.148-1-0-gc9ba2fbc
[ 8.140891] usbcore: registered new interface driver ums-alauda
[ 8.147209] usbcore: registered new interface driver ums-cypress
[ 8.153586] usbcore: registered new interface driver ums-datafab
[ 8.159983] usbcore: registered new interface driver ums-freecom
[ 8.166362] usbcore: registered new interface driver ums-isd200
[ 8.172676] usbcore: registered new interface driver ums-jumpshot
[ 8.179135] usbcore: registered new interface driver ums-karma
[ 8.185374] usbcore: registered new interface driver ums-sddr09
[ 8.191690] usbcore: registered new interface driver ums-sddr55
[ 8.198025] usbcore: registered new interface driver ums-usbat
[ 8.204850] usbcore: registered new interface driver usbserial_generic
[ 8.211435] usbserial: USB Serial support registered for generic
[ 8.223016] xt_time: kernel timezone is -0000
[ 8.261499] PPP generic driver version 2.4.2
[ 8.266489] NET: Registered PF_PPPOX protocol family
[ 8.288934] usbcore: registered new interface driver qcserial
[ 8.294731] usbserial: USB Serial support registered for Qualcomm USB modem
[ 8.308750] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 14.748553] mvneta f1030000.ethernet eth1: configuring for fixed/rgmii link mode
[ 14.756571] mvneta f1030000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 14.764714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 14.778300] mv88e6085 f1072004.mdio-mii:10 lan0: configuring for phy/gmii link mode
[ 14.861339] br-lan: port 1(lan0) entered blocking state
[ 14.866617] br-lan: port 1(lan0) entered disabled state
[ 14.919717] device lan0 entered promiscuous mode
[ 14.924357] device eth1 entered promiscuous mode
[ 15.090220] mv88e6085 f1072004.mdio-mii:10 lan1: configuring for phy/gmii link mode
[ 15.171433] br-lan: port 2(lan1) entered blocking state
[ 15.176719] br-lan: port 2(lan1) entered disabled state
[ 15.225841] device lan1 entered promiscuous mode
[ 15.250754] mv88e6085 f1072004.mdio-mii:10 lan2: configuring for phy/gmii link mode
[ 15.316666] br-lan: port 3(lan2) entered blocking state
[ 15.321924] br-lan: port 3(lan2) entered disabled state
[ 15.370821] device lan2 entered promiscuous mode
[ 15.396161] mv88e6085 f1072004.mdio-mii:10 lan3: configuring for phy/gmii link mode
[ 15.462963] br-lan: port 4(lan3) entered blocking state
[ 15.468275] br-lan: port 4(lan3) entered disabled state
[ 15.522772] device lan3 entered promiscuous mode
[ 15.548191] mv88e6085 f1072004.mdio-mii:10 lan4: configuring for phy/gmii link mode
[ 15.620297] br-lan: port 5(lan4) entered blocking state
[ 15.625544] br-lan: port 5(lan4) entered disabled state
[ 15.675933] device lan4 entered promiscuous mode
[ 15.777854] mvneta f1034000.ethernet eth2: PHY [f1072004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL)
[ 15.787757] mvneta f1034000.ethernet eth2: configuring for phy/sgmii link mode
[ 18.065544] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Up - 1Gbps/Full - flow control off
[ 18.075626] br-lan: port 1(lan0) entered blocking state
[ 18.080925] br-lan: port 1(lan0) entered forwarding state
[ 18.107793] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Router Turris successfully started.
@tuomaz Sigh. OK, in that case I would like to request one more test of you: testing whether using the old stock U-Boot helps. The process should be as follows:
opkg update
opkg install mtd
cd /tmp
wget https://repo.turris.cz/archive/omnia/3.10/nor_fw/uboot-turris-omnia-spl.kwb
mtd write uboot-turris-omnia-spl.kwb U-Boot
reboot
After the reboot, in U-Boot command prompt, please reset the environment to default and save it.
env default -a
env save
After that please power off the board for several seconds, then power it up again.
Please let me know if this gets rid of the issues. If not, then that would mean that these issues are caused by something else from the update.
Flashed old U-Boot according to instructions, powered off Omnia for 3 minutes. Now it is up again and Iām monitoring itā¦
It just passed 24h uptime. It has not happened since I upgraded to 6.5.0 / new U-Boot. Keeping my fingers crossed 
It now has an uptime of almost 4 days. It looks like the old U-Boot fixed it for my Omnia. Iām very happy 
, thank you all.
Now, when it looks like it is working, Iām planning to use the Omnia as my main router again, @mbehun is there something you want me to test before before Iām going back to 6.5.2 and start using it ānormallyā. I will not be able to test things thenā¦
Well I am not happy at all 
Because this means that the old DDR training code I incorporated into the new U-Boot is somehow incomplete or something. I will try to find a board in the office that has DDR problems with new U-Boot and work this out. Hopefully I will be successful in finding such a board.
I understand. I will start using my Omnia as my router again, but let me know if you want to test something, I might be able to help.
Last question: any idea how many are hit by this issue? I donāt see that much activity here on the forum about this issue.
This topic was automatically closed 3 days after the last reply. New replies are no longer allowed.