Mismatched phy regions on WiFi

Omnia hardware Omnia HW problems
1

In my seemingly never ending attempts to get a stable 5Ghz WiFi signal out of my Omnia I was doing some digging around in the command line and noticed that “iw reg get” is confused about the regions. My global setting is for the UK bu the phys are set for the US. Could this be causing problems and how can I fix this?

root@turris:~# iw reg get
global
country GB: DFS-ETSI
        (2400 - 2483 @ 40), (N/A, 20), (N/A)
        (5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
        (5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
        (5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
        (5725 - 5875 @ 80), (N/A, 13), (N/A)
        (57000 - 66000 @ 2160), (N/A, 40), (N/A)

phy#1
country US: DFS-FCC
        (2402 - 2472 @ 40), (N/A, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
        (5735 - 5835 @ 80), (N/A, 30), (N/A)
        (57240 - 71000 @ 2160), (N/A, 40), (N/A)

phy#0
country US: DFS-FCC
        (2402 - 2472 @ 40), (N/A, 30), (N/A)
        (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
        (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
        (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
        (5735 - 5835 @ 80), (N/A, 30), (N/A)
        (57240 - 71000 @ 2160), (N/A, 40), (N/A)
2

To add to my worries this is what I get when rmmod/modprobe’ing my ath10k:

[44687.205324] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[44688.137140] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256

[44688.154233] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
[44688.160351] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta
: 0'
[44688.168403] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 21000 iram: 25960'
[44688.234390] ath10k_pci 0000:02:00.0: htt-ver 2.2 wmi-op 2 htt-op 2 cal otp max-sta
128 raw 0 hwcrypto 1
[44688.356536] ath: EEPROM regdomain: 0x0
[44688.356541] ath: EEPROM indicates default country code should be used
[44688.356543] ath: doing EEPROM country->regdmn map search
[44688.356546] ath: country maps to regdmn code: 0x3a
[44688.356548] ath: Country alpha2 being used: US
[44688.356550] ath: Regpair used: 0x3a
[44688.356658] ath: EEPROM regdomain: 0x833a
[44688.356660] ath: EEPROM indicates we should expect a country code
[44688.356663] ath: doing EEPROM country->regdmn map search
[44688.356665] ath: country maps to regdmn code: 0x37
[44688.356667] ath: Country alpha2 being used: GB
[44688.356668] ath: Regpair used: 0x37
[44688.356670] ath: regdomain 0x833a dynamically updated by user
[44689.402690] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256

[44689.419819] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
[44689.425893] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta
: 0'
[44689.433928] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 21000 iram: 25960'
[44689.499996] ath10k_pci 0000:02:00.0: pdev param 0 not supported by firmware
[44689.514733] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready