I have a TO that was working fine with 3.9, and now is behaving badly with 3.10.
Rather than upgrade to 3.10.1 immediately, I would like to roll back to 3.9. Is there any way of obtaining a 3.9 medkit image?
I see this link, but it is a tar.xz, and not a tar.gz file…
https://repo.turris.cz/archive/turris/3.9.6/medkit/
Hello,
can I know, which issues do you have on 3.10?
The wireless card in slot 3 just disappears sometimes. One boot it is there, next time you boot it is not (as evidenced by a lspci). This behaviour started in 3.10.
Is something in dmesg, when the 5 GHz card is not recognized?
I didn’t make it very clear - it is slots 1 and 3 that have the problem - I have tried 3 different cards in slot 3, and sometimes the card if ‘found’, and sometimes not - no pattern found so far. All these cards seem to work OK in slot 2 - the card in slot 2 is always found.
The mSATA card in slot 1 is same as slot 3 - sometimes found sometimes not.
Here is a dmesg with both slot 1 and 3 working OK.
login as: root
root@192.168.1.1's password:
BusyBox v1.25.1 (2018-05-04 09:08:46 CEST) built-in shell (ash)
_______ _ _ _____ _____ _____ _____
|__ __|| | | || __ \ | __ \ |_ _| / ____|
| | | | | || |__) || |__) | | | | (___
| | | | | || _ / | _ / | | \___ \
| | | |__| || | \ \ | | \ \ _| |_ ____) |
|_| \____/ |_| \_\|_| \_\|_____||_____/
root@turris:~# lspci
00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
02:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn Wireless Network Adapter (rev 01)
03:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter (rev ff)
root@turris:~# dmesg
[ 9.840843] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 9.847234] ata1.00: supports DRM functions and may not be fully accessible
[ 9.854225] ata1.00: ATA-9: Samsung SSD 850 EVO mSATA 250GB, EMT41B6Q, max UDMA/133
[ 9.861905] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 9.869244] ata1.00: supports DRM functions and may not be fully accessible
[ 9.876546] ata1.00: configured for UDMA/133
[ 9.880830] ata1: EH complete
[ 9.884002] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 850 1B6Q PQ: 0 ANSI: 5
[ 9.892496] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[ 9.900200] random: procd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[ 9.909254] sd 0:0:0:0: [sda] Write Protect is off
[ 9.914067] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 9.914104] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.924829] sda: sda1
[ 9.927592] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 11.232671] mount_root: mounting /dev/root
[ 11.262793] BTRFS info (device mmcblk0p1): disk space caching is enabled
[ 11.270124] mount_root: loading kmods from internal overlay
[ 11.484258] block: attempting to load /etc/config/fstab
[ 11.490599] block: extroot: not configured
[ 11.497217] procd: - early -
[ 11.500124] procd: - watchdog -
[ 11.605065] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.631589] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.667037] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.691565] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.727058] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.751686] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.787328] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.811771] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 11.847475] random: jshn: uninitialized urandom read (4 bytes read, 24 bits of entropy available)
[ 12.072688] procd: - ubus -
[ 13.078291] procd: - init -
[ 13.135688] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 13.148438] NET: Registered protocol family 38
[ 13.164068] md: linear personality registered for level -1
[ 13.169927] md: raid0 personality registered for level 0
[ 13.175937] md: raid1 personality registered for level 1
[ 13.182290] md: raid10 personality registered for level 10
[ 13.188153] async_tx: api initialized (async)
[ 13.195469] md: raid6 personality registered for level 6
[ 13.200796] md: raid5 personality registered for level 5
[ 13.206133] md: raid4 personality registered for level 4
[ 13.213315] FS-Cache: Loaded
[ 13.216642] md: multipath personality registered for level -4
[ 13.223629] NET: Registered protocol family 8
[ 13.227996] NET: Registered protocol family 20
[ 13.236186] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 13.247021] Key type dns_resolver registered
[ 13.254166] NET: Registered protocol family 33
[ 13.258624] Key type rxrpc registered
[ 13.262307] Key type rxrpc_s registered
[ 13.269242] kAFS: Red Hat AFS client v0.1 registering.
[ 13.274450] FS-Cache: Netfs 'afs' registered for caching
[ 13.308924] RPC: Registered named UNIX socket transport module.
[ 13.314877] RPC: Registered udp transport module.
[ 13.319591] RPC: Registered tcp transport module.
[ 13.324315] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.348613] NFS: Registering the id_resolver key type
[ 13.353717] Key type id_resolver registered
[ 13.357909] Key type id_legacy registered
[ 13.362563] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 13.371819] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 13.381655] RxRPC: Registered security type 2 'rxkad'
[ 13.398112] tun: Universal TUN/TAP device driver, 1.6
[ 13.403206] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 13.412993] sit: IPv6 over IPv4 tunneling driver
[ 13.421683] gre: GRE over IPv4 demultiplexor driver
[ 13.427148] ip_gre: GRE over IPv4 tunneling driver
[ 13.446878] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.455434] PPP generic driver version 2.4.2
[ 13.462875] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.472070] cryptodev: driver 1.8 loaded.
[ 13.480191] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 13.488235] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 13.561686] pci 0000:00:03.0: enabling device (0140 -> 0142)
[ 13.580866] ath10k_pci 0000:03:00.0: Refused to change power state, currently in D3
[ 13.618700] ath10k_pci 0000:03:00.0: failed to wake up device : -110
[ 13.625146] ath10k_pci: probe of 0000:03:00.0 failed with error -110
[ 13.634233] u32 classifier
[ 13.636946] input device check on
[ 13.640614] Actions configured
[ 13.644592] Mirror/redirect action on
[ 13.649511] GACT probability on
[ 13.657578] netem: version 1.3
[ 13.666670] fuse init (API version 7.23)
[ 13.681637] usbcore: registered new interface driver cdc_wdm
[ 13.690249] Ebtables v2.0 registered
[ 13.695236] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.707157] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 13.864171] Netfilter messages via NETLINK v0.30.
[ 13.869717] PPP MPPE Compression module registered
[ 13.875044] NET: Registered protocol family 24
[ 13.882933] usbcore: registered new interface driver ums-alauda
[ 13.889608] usbcore: registered new interface driver ums-cypress
[ 13.896546] usbcore: registered new interface driver ums-datafab
[ 13.903369] usbcore: registered new interface driver ums-freecom
[ 13.910244] usbcore: registered new interface driver ums-isd200
[ 13.917195] usbcore: registered new interface driver ums-jumpshot
[ 13.924121] usbcore: registered new interface driver ums-karma
[ 13.931166] usbcore: registered new interface driver ums-sddr09
[ 13.937993] usbcore: registered new interface driver ums-sddr55
[ 13.944953] usbcore: registered new interface driver ums-usbat
[ 13.956695] usbcore: registered new interface driver usbserial
[ 13.962585] usbcore: registered new interface driver usbserial_generic
[ 13.969151] usbserial: USB Serial support registered for generic
[ 13.983885] xt_time: kernel timezone is -0000
[ 14.002114] usbcore: registered new interface driver cdc_ether
[ 14.012490] ctnetlink v0.93: registering with nfnetlink.
[ 14.021440] usbcore: registered new interface driver qmi_wwan
[ 14.028383] usbcore: registered new interface driver rndis_host
[ 14.041963] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 14.053982] ath: EEPROM regdomain: 0x0
[ 14.053986] ath: EEPROM indicates default country code should be used
[ 14.053989] ath: doing EEPROM country->regdmn map search
[ 14.053993] ath: country maps to regdmn code: 0x3a
[ 14.053996] ath: Country alpha2 being used: US
[ 14.053999] ath: Regpair used: 0x3a
[ 14.060780] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 14.062186] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xf1a40000, irq=108
[ 14.070720] usbcore: registered new interface driver option
[ 14.076378] usbserial: USB Serial support registered for GSM modem (1-port)
[ 14.084085] usbcore: registered new interface driver qcserial
[ 14.089874] usbserial: USB Serial support registered for Qualcomm USB modem
[ 16.963507] random: nonblocking pool is initialized
[ 19.369707] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.452538] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.456015] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 19.919540] BTRFS: device fsid 9012b050-76dd-4e3a-87c6-7c60c25c7cdb devid 1 transid 275509 /dev/sda1
[ 20.909344] device eth0 entered promiscuous mode
[ 20.910802] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.932232] device eth2 entered promiscuous mode
[ 21.012441] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 22.900931] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 22.900965] br-lan: port 1(eth0) entered forwarding state
[ 22.900994] br-lan: port 1(eth0) entered forwarding state
[ 22.901051] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.930942] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[ 22.930982] br-lan: port 2(eth2) entered forwarding state
[ 22.931015] br-lan: port 2(eth2) entered forwarding state
[ 23.725056] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 23.732347] ata1: irq_stat 0x80400000, PHY RDY changed
[ 23.737512] ata1: hard resetting link
[ 24.480907] ata1: SATA link down (SStatus 0 SControl 300)
[ 24.900891] br-lan: port 1(eth0) entered forwarding state
[ 24.930876] br-lan: port 2(eth2) entered forwarding state
[ 26.972833] ata1: hard resetting link
[ 27.320877] ata1: SATA link down (SStatus 0 SControl 300)
[ 27.320892] ata1: limiting SATA link speed to 1.5 Gbps
[ 30.632973] ata1: hard resetting link
[ 31.180846] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 31.182477] ata1.00: supports DRM functions and may not be fully accessible
[ 31.183267] ata1.00: supports DRM functions and may not be fully accessible
[ 31.183702] ata1.00: configured for UDMA/133
[ 31.183709] ata1: EH complete
[ 38.845510] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 38.852769] ata1: irq_stat 0x80400000, PHY RDY changed
[ 38.857925] ata1: hard resetting link
[ 39.960853] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 39.962465] ata1.00: supports DRM functions and may not be fully accessible
[ 39.963257] ata1.00: supports DRM functions and may not be fully accessible
[ 39.963691] ata1.00: configured for UDMA/133
[ 39.963699] ata1: EH complete
[ 40.541375] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 40.548619] ata1: irq_stat 0x80400000, PHY RDY changed
[ 40.553791] ata1: hard resetting link
[ 41.300854] ata1: SATA link down (SStatus 0 SControl 310)
[ 42.199683] ata1: hard resetting link
[ 42.740848] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 42.742488] ata1.00: supports DRM functions and may not be fully accessible
[ 42.743279] ata1.00: supports DRM functions and may not be fully accessible
[ 42.743713] ata1.00: configured for UDMA/133
[ 42.743720] ata1: EH complete
[ 42.893152] ata1.00: limiting speed to UDMA/100:PIO4
[ 42.893161] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 42.900405] ata1: irq_stat 0x80400000, PHY RDY changed
[ 42.905579] ata1: hard resetting link
[ 43.650851] ata1: SATA link down (SStatus 0 SControl 310)
[ 48.650849] ata1: hard resetting link
[ 49.000901] ata1: SATA link down (SStatus 0 SControl 310)
[ 54.000850] ata1: hard resetting link
[ 54.350847] ata1: SATA link down (SStatus 0 SControl 310)
[ 54.350858] ata1.00: disabled
[ 54.350873] ata1: EH complete
[ 54.350894] ata1.00: detaching (SCSI 0:0:0:0)
[ 54.351245] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 54.351934] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
[ 54.351942] sd 0:0:0:0: [sda] Stopping disk
[ 54.351960] sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
[ 85.494162] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 85.501591] ata1: irq_stat 0x80000040, connection status changed
[ 85.507619] ata1: hard resetting link
[ 86.450849] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 86.452450] ata1.00: supports DRM functions and may not be fully accessible
[ 86.452457] ata1.00: ATA-9: Samsung SSD 850 EVO mSATA 250GB, EMT41B6Q, max UDMA/133
[ 86.452462] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32)
[ 86.453117] ata1.00: supports DRM functions and may not be fully accessible
[ 86.453482] ata1.00: configured for UDMA/133
[ 86.453492] ata1: EH complete
[ 86.453701] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 850 1B6Q PQ: 0 ANSI: 5
[ 86.454282] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[ 86.454388] sd 0:0:0:0: [sda] Write Protect is off
[ 86.454396] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 86.454430] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 86.456104] sda: sda1
[ 86.456538] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 88.111981] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 88.119224] ata1: irq_stat 0x80400000, PHY RDY changed
[ 88.124398] ata1: hard resetting link
[ 89.070847] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 89.072462] ata1.00: supports DRM functions and may not be fully accessible
[ 89.073251] ata1.00: supports DRM functions and may not be fully accessible
[ 89.073685] ata1.00: configured for UDMA/133
[ 89.073692] ata1: EH complete
[ 94.884856] ata1: exception Emask 0x10 SAct 0x0 SErr 0x10002 action 0xe frozen
[ 94.892111] ata1: irq_stat 0x80400000, PHY RDY changed
[ 94.897267] ata1: hard resetting link
[ 95.840847] ata1: SATA link down (SStatus 0 SControl 300)
[ 100.840849] ata1: hard resetting link
[ 101.190846] ata1: SATA link down (SStatus 0 SControl 300)
[ 101.190858] ata1: limiting SATA link speed to 1.5 Gbps
[ 106.190849] ata1: hard resetting link
[ 106.540846] ata1: SATA link down (SStatus 0 SControl 310)
[ 106.540857] ata1.00: disabled
[ 106.540874] ata1: EH complete
[ 106.540892] ata1.00: detaching (SCSI 0:0:0:0)
[ 106.541236] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 106.542074] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=0x00
[ 106.542082] sd 0:0:0:0: [sda] Stopping disk
[ 106.542100] sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=0x00
[ 160.416554] ata1: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen
[ 160.423983] ata1: irq_stat 0x80000040, connection status changed
[ 160.430017] ata1: hard resetting link
[ 161.170845] ata1: SATA link down (SStatus 0 SControl 300)
[ 161.170860] ata1: EH complete
[ 170.011267] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 170.011288] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
root@turris:~#
Here is a dmesg after a reboot (no other changes) - both missing.
login as: root
root@192.168.1.1's password:
BusyBox v1.25.1 (2018-05-04 09:08:46 CEST) built-in shell (ash)
_______ _ _ _____ _____ _____ _____
|__ __|| | | || __ \ | __ \ |_ _| / ____|
| | | | | || |__) || |__) | | | | (___
| | | | | || _ / | _ / | | \___ \
| | | |__| || | \ \ | | \ \ _| |_ ____) |
|_| \____/ |_| \_\|_| \_\|_____||_____/
root@turris:~# lspci
00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
02:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn Wireless Network Adapter (rev 01)
root@turris:~# dmesg
[ 4.194265] mvneta f1034000.ethernet eth1: Using hardware mac address d8:58:d7:00:63:5e
[ 4.203044] mvneta f1070000.ethernet eth2: Using hardware mac address d8:58:d7:00:63:5f
[ 4.211290] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[ 4.490945] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.496382] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.721055] i2c /dev entries driver
[ 4.725281] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
[ 4.732060] i2c i2c-0: Added multiplexed i2c bus 1
[ 4.736928] i2c i2c-0: Added multiplexed i2c bus 2
[ 4.741803] i2c i2c-0: Added multiplexed i2c bus 3
[ 4.746667] i2c i2c-0: Added multiplexed i2c bus 4
[ 4.751541] i2c i2c-0: Added multiplexed i2c bus 5
[ 4.756404] i2c i2c-0: Added multiplexed i2c bus 6
[ 4.761278] i2c i2c-0: Added multiplexed i2c bus 7
[ 4.768086] i2c i2c-0: Added multiplexed i2c bus 8
[ 4.772901] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547
[ 4.780474] orion_wdt: Initial timeout 171 sec
[ 4.785066] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[ 4.793308] sdhci: Secure Digital Host Controller Interface driver
[ 4.799501] sdhci: Copyright(c) Pierre Ossman
[ 4.804006] sdhci-pxav3 f10d8000.sdhci: No vmmc regulator found
[ 4.809939] sdhci-pxav3 f10d8000.sdhci: No vqmmc regulator found
[ 4.860947] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 4.868397] sdhci-pltfm: SDHCI platform and OF driver helper
[ 4.883392] NET: Registered protocol family 10
[ 4.888306] NET: Registered protocol family 17
[ 4.892790] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 4.905446] Bridge firewalling registered
[ 4.909467] 8021q: 802.1Q VLAN Support v1.8
[ 4.913733] Registering SWP/SWPB emulation handler
[ 4.918866] BTRFS: using crc32c-generic for crc32c
[ 4.923932] Btrfs loaded, integrity-checker=on
[ 4.928980] mvsw61xx 10.mvsw61xx: Found MV88E6176 at f1072004.mdio-mii:10
[ 4.935817] mvsw61xx 10.mvsw61xx: Using indirect addressing
[ 4.973901] mmc0: MAN_BKOPS_EN bit is not set
[ 4.981414] mmc0: new high speed MMC card at address 0001
[ 4.987028] mmcblk0: mmc0:0001 H8G4a▒ 7.28 GiB
[ 4.991650] mmcblk0boot0: mmc0:0001 H8G4a▒ partition 1 4.00 MiB
[ 4.997652] mmcblk0boot1: mmc0:0001 H8G4a▒ partition 2 4.00 MiB
[ 5.003684] mmcblk0rpmb: mmc0:0001 H8G4a▒ partition 3 4.00 MiB
[ 5.010568] mmcblk0: p1
[ 5.013117] armada38x-rtc f10a3800.rtc: setting system clock to 2018-05-12 09:01:49 UTC (1526115709)
[ 5.022366] Waiting 2 sec before mounting root device...
[ 7.033590] BTRFS: device fsid a28dbad5-ecea-480b-be1a-1ed024233c8f devid 1 transid 130 /dev/root
[ 7.043085] BTRFS info (device mmcblk0p1): disk space caching is enabled
[ 7.049802] BTRFS: has skinny extents
[ 7.057399] BTRFS: detected SSD devices, enabling SSD mode
[ 7.090956] VFS: Mounted root (btrfs filesystem) on device 0:13.
[ 7.097101] Freeing unused kernel memory: 284K
[ 7.147806] init: Console is alive
[ 7.151291] init: - watchdog -
[ 7.506954] usbcore: registered new interface driver usbfs
[ 7.512512] usbcore: registered new interface driver hub
[ 7.517875] usbcore: registered new device driver usb
[ 7.524794] exFAT: Version 1.2.9
[ 7.542376] JFS: nTxBlock = 8192, nTxLock = 65536
[ 7.603292] SGI XFS with security attributes, no debug enabled
[ 7.610710] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.617607] ehci-platform: EHCI generic platform driver
[ 7.623232] ehci-orion: EHCI orion driver
[ 7.627351] orion-ehci f1058000.usb: EHCI Host Controller
[ 7.632787] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 7.640433] orion-ehci f1058000.usb: irq 39, io mem 0xf1058000
[ 7.660948] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 7.667139] hub 1-0:1.0: USB hub found
[ 7.670909] hub 1-0:1.0: 1 port detected
[ 7.675946] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.685466] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 7.690803] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 7.698416] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 7.706988] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[ 7.713002] hub 2-0:1.0: USB hub found
[ 7.716772] hub 2-0:1.0: 1 port detected
[ 7.720799] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 7.726140] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 7.733691] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.742016] hub 3-0:1.0: USB hub found
[ 7.745784] hub 3-0:1.0: 1 port detected
[ 7.749851] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 7.755198] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 7.762795] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 7.771364] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[ 7.777369] hub 4-0:1.0: USB hub found
[ 7.781148] hub 4-0:1.0: 1 port detected
[ 7.785168] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 7.790495] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 7.798035] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.806352] hub 5-0:1.0: USB hub found
[ 7.810118] hub 5-0:1.0: 1 port detected
[ 7.815290] usbcore: registered new interface driver usb-storage
[ 7.990946] usb 1-1: new full-speed USB device number 2 using orion-ehci
[ 8.154593] init: - preinit -
[ 11.203461] mount_root: mounting /dev/root
[ 11.232151] BTRFS info (device mmcblk0p1): disk space caching is enabled
[ 11.239482] mount_root: loading kmods from internal overlay
[ 11.450634] block: attempting to load /etc/config/fstab
[ 11.456930] block: extroot: not configured
[ 11.463421] procd: - early -
[ 11.466327] procd: - watchdog -
[ 11.563132] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.589729] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.625346] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.649921] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.685414] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.709774] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.745270] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.769818] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.805596] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 11.830123] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[ 12.033720] procd: - ubus -
[ 13.038853] procd: - init -
[ 13.096980] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 13.109771] NET: Registered protocol family 38
[ 13.125518] md: linear personality registered for level -1
[ 13.131413] md: raid0 personality registered for level 0
[ 13.137426] md: raid1 personality registered for level 1
[ 13.143856] md: raid10 personality registered for level 10
[ 13.149721] async_tx: api initialized (async)
[ 13.157085] md: raid6 personality registered for level 6
[ 13.162433] md: raid5 personality registered for level 5
[ 13.167756] md: raid4 personality registered for level 4
[ 13.174927] FS-Cache: Loaded
[ 13.178263] md: multipath personality registered for level -4
[ 13.185200] NET: Registered protocol family 8
[ 13.189568] NET: Registered protocol family 20
[ 13.197747] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 13.208588] Key type dns_resolver registered
[ 13.215728] NET: Registered protocol family 33
[ 13.220184] Key type rxrpc registered
[ 13.223880] Key type rxrpc_s registered
[ 13.230885] kAFS: Red Hat AFS client v0.1 registering.
[ 13.236092] FS-Cache: Netfs 'afs' registered for caching
[ 13.270577] RPC: Registered named UNIX socket transport module.
[ 13.276541] RPC: Registered udp transport module.
[ 13.281266] RPC: Registered tcp transport module.
[ 13.285979] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.310265] NFS: Registering the id_resolver key type
[ 13.315391] Key type id_resolver registered
[ 13.319584] Key type id_legacy registered
[ 13.324258] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 13.333463] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 13.343299] RxRPC: Registered security type 2 'rxkad'
[ 13.359802] tun: Universal TUN/TAP device driver, 1.6
[ 13.364889] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 13.374597] sit: IPv6 over IPv4 tunneling driver
[ 13.381282] gre: GRE over IPv4 demultiplexor driver
[ 13.386837] ip_gre: GRE over IPv4 tunneling driver
[ 13.406676] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.415335] PPP generic driver version 2.4.2
[ 13.422603] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.431994] cryptodev: driver 1.8 loaded.
[ 13.440247] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 13.448295] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 13.526927] u32 classifier
[ 13.529642] input device check on
[ 13.533328] Actions configured
[ 13.537222] Mirror/redirect action on
[ 13.542025] GACT probability on
[ 13.549533] netem: version 1.3
[ 13.558166] fuse init (API version 7.23)
[ 13.573716] usbcore: registered new interface driver cdc_wdm
[ 13.582455] Ebtables v2.0 registered
[ 13.587388] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.599331] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 13.754291] Netfilter messages via NETLINK v0.30.
[ 13.759836] PPP MPPE Compression module registered
[ 13.765188] NET: Registered protocol family 24
[ 13.773054] usbcore: registered new interface driver ums-alauda
[ 13.779731] usbcore: registered new interface driver ums-cypress
[ 13.786660] usbcore: registered new interface driver ums-datafab
[ 13.793483] usbcore: registered new interface driver ums-freecom
[ 13.800357] usbcore: registered new interface driver ums-isd200
[ 13.807290] usbcore: registered new interface driver ums-jumpshot
[ 13.814240] usbcore: registered new interface driver ums-karma
[ 13.821284] usbcore: registered new interface driver ums-sddr09
[ 13.828112] usbcore: registered new interface driver ums-sddr55
[ 13.835068] usbcore: registered new interface driver ums-usbat
[ 13.846830] usbcore: registered new interface driver usbserial
[ 13.852723] usbcore: registered new interface driver usbserial_generic
[ 13.859291] usbserial: USB Serial support registered for generic
[ 13.874110] xt_time: kernel timezone is -0000
[ 13.892322] usbcore: registered new interface driver cdc_ether
[ 13.902684] ctnetlink v0.93: registering with nfnetlink.
[ 13.911635] usbcore: registered new interface driver qmi_wwan
[ 13.918565] usbcore: registered new interface driver rndis_host
[ 13.932097] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 13.944146] ath: EEPROM regdomain: 0x0
[ 13.944150] ath: EEPROM indicates default country code should be used
[ 13.944153] ath: doing EEPROM country->regdmn map search
[ 13.944158] ath: country maps to regdmn code: 0x3a
[ 13.944160] ath: Country alpha2 being used: US
[ 13.944163] ath: Regpair used: 0x3a
[ 13.951012] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.952453] ieee80211 phy0: Atheros AR9300 Rev:4 mem=0xf1840000, irq=108
[ 13.961045] usbcore: registered new interface driver option
[ 13.966678] usbserial: USB Serial support registered for GSM modem (1-port)
[ 13.974411] usbcore: registered new interface driver qcserial
[ 13.980200] usbserial: USB Serial support registered for Qualcomm USB modem
[ 16.853438] random: nonblocking pool is initialized
[ 19.258206] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.342636] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.346087] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 20.756754] device eth0 entered promiscuous mode
[ 20.758040] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.779803] device eth2 entered promiscuous mode
[ 20.863176] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 22.751055] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 22.751092] br-lan: port 1(eth0) entered forwarding state
[ 22.751125] br-lan: port 1(eth0) entered forwarding state
[ 22.751176] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.771113] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[ 22.771141] br-lan: port 2(eth2) entered forwarding state
[ 22.771166] br-lan: port 2(eth2) entered forwarding state
[ 24.750995] br-lan: port 1(eth0) entered forwarding state
[ 24.770991] br-lan: port 2(eth2) entered forwarding state
[ 24.861428] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 24.861455] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
I can get TTL dmesgs tomorrow when I get my USB/TTL card back.