Hi there!
After watching this “Van Tech Corner Replace ISP ONU with PON Stick” video on youtube, I managed this module to work (ISP MZNet Fibra from Brazil, VLAN ID 2000) in my Turris Omnia running TOS 6.0.4:
Perhaps, the 2.5Gb mode is not recognized. I can set it on the ODI telnet cmdline (as reported in this repo), but it is downgrading to 1Gb mode, as below:
ODI boot log:
net_device_ops yet
<6>eth0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
<6>eth0.2 (): not using net_device_ops yet
<6>eth0.2: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
<6>eth0.3 (): not using net_device_ops yet
<6>eth0.3: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
<6>nas0 (): not using net_device_ops yet
<6>nas0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
<4>>>>> Set nas0 carrier off !!!
<6>pon0 (): not using net_device_ops yet
<6>pon0: RTL-8686 at 0xb8012000, 00:00:00:01:00:02, IRQ 26
<4>RTL8686 GMAC Probing..
<4>first entry: 0, portmask 127, rx: 802334ec
<4>nas0 -> 0x4
<4>Init RTK Driver Module....*** [RT_DBG] drivers/net/rtl86900/sdk/src//dal/rtl9602c/dal_rtl9602c_classify.c:3567: In function 'dal_rtl9602c_classify_unmatchAction_set' action 2
<4>
<4>OK
<4>Init RTK Core Dev Module....OK
<4>
<4> rtdrv_init !!! for netfilter
<4>pkt_redirect_init complete
<5>interrupt broadcaster init ok!
<4>u32 classifier
<4>nf_conntrack version 0.5.0 (479 buckets, 1916 max)
<6>ip_tables: (C) 2000-2006 Netfilter Core Team
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<5>Bridge firewalling registered
<6>Ebtables v2.0 registered
<6>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
<6>All bugs added by David S. Miller <davem@redhat.com>
<4>Realtek GPIO Driver for Flash Reload Default
<5>physmap platform flash device: 0b000000 at 14000000
<4>Luna SPI NOR FLASH G3 driver-C22017/MMIO16-1 <5>master->name physmap-flash
<5>cmd: cmdlinepart
<5>14 cmdlinepart partitions found on MTD device physmap-flash
<5>Creating 14 MTD partitions on "physmap-flash":
<5>0x000000000000-0x000000040000 : "boot"
<5>0x000000040000-0x000000042000 : "env"
<5>0x000000042000-0x000000044000 : "env2"
<5>0x000000044000-0x000000080000 : "config"
<5>0x000000080000-0x0000001cc000 : "k0"
<5>0x0000001cc000-0x000000440000 : "r0"
<5>0x000000440000-0x00000058c000 : "k1"
<5>0x00000058c000-0x000000800000 : "r1"
<5>0x000000000000-0x000000001000 : "Partition_008"
<5>0x000000000000-0x000000001000 : "Partition_009"
<5>0x000000000000-0x000000001000 : "Partition_010"
<5>0x000000000000-0x000000001000 : "Partition_011"
<5>0x000000080000-0x0000001cc000 : "linux"
<5>0x0000001cc000-0x000000440000 : "rootfs"
<4>VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
<6>Freeing unused kernel memory: 100k freed
<4>re8670_open 3341
<4>omci platform attached!
<4>*** [RT_ERR] drivers/net/rtl86900/sdk/src//dal/rtl9602c/dal_rtl9602c_ponmac.c:1039: In function '_rtl9602c_ponMacGponModeV2_set'
<4> Error Code: 0x8848
<4>
<4>*** [RT_DBG] drivers/net/rtl86900/sdk/src//dal/rtl9602c/dal_rtl9602c_classify.c:3567: In function 'dal_rtl9602c_classify_unmatchAction_set' action 1
<4>
<4>*** [RT_DBG] drivers/net/rtl86900/sdk/src//dal/rtl9602c/dal_rtl9602c_classify.c:3567: In function 'dal_rtl9602c_classify_unmatchAction_set' action 1
<4>
<3>register_gpon_evt_state: register gpon event state Successfully !
<4>priority: 0, portmask 127, rx: 802334ec
<4>insert here, priority: 7, portmask 255, rx: c026b34c
<4>change mode to 4(HiSGMII PHY)
<4>send to user app (5) fail (-1)
<4>write watchdog_flag to 0x00000001
<4>[Kthread : watchdog ] init complete!
<4>************ Watchdog Setting ****************
<4>WDT_E=1, (1-enable, 0-disable)
<4>LX(MHz)=200
<4>WDT_CLK_SC=3
<4>PH1_TO=31
<4>PH2_TO=0
<4>WDT_RESET_MODE=0
<4>**********************************************
<4>port 2 assign to pon0
<4>pon0 -> 0x4
<6>device eth0 entered promiscuous mode
<4>priority: 7, portmask 255, rx: c026b34c
<4>priority: 0, portmask 127, rx: 802334ec
<4>insert here, priority: 4, portmask 4, rx: 80172968
<6>br0: port 1(eth0) entering learning state
<4>drivers/net/rtl86900/sdk/src/rtk/pon_led.c:1152 led sw blink init complete!
<6>br0: port 1(eth0) entering forwarding state
<4>drivers/net/rtl86900/sdk/src/module/lan_sds/lan_sds_main.c:679 SFP_TASK_MASK_EEPROM_128TO247
<4>change mode to 1(Fiber 1G)
<4>eth0: received packet with own address as source address 38-3a-21-27-eb-86 loop intf=0 0
<4>eth0: received packet with own address as source address 38-3a-21-27-eb-86 loop intf=0 0
Turris boot log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.15.82 (packaging@turris.cz) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 8.4.0 r16803+125-784565b6a0) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Sun Dec 11 23:19:41 2022
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Turris Omnia
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14732 r8192 d22132 u45056
[ 0.000000] pcpu-alloc: s14732 r8192 d22132 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: earlyprintk rootwait console=ttyS0,115200 rootfstype=btrfs root=PARTUUID=00000000-01 rootflags=commit=5,subvol=@ rw cfg80211.freg=**
[ 0.000000] Bootloader command line not present
[ 0.000000] Unknown kernel command line parameters "earlyprintk mangled_fs=btrfs", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2063496K/2097152K available (9216K kernel code, 669K rwdata, 2180K rodata, 1024K init, 258K bss, 33656K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] Registering MPIC SoC Error Interrupt Controller
[ 0.000000] L2C: DT/platform modifies aux control register: 0x06070000 -> 0x16070000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000001] sched_clock: 64 bits at 800MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.000018] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xb881274fa3, max_idle_ns: 440795210636 ns
[ 0.000036] Switching to timer-based delay loop, resolution 1ns
[ 0.000180] Ignoring duplicate/late registration of read_current_timer delay
[ 0.000187] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000374] Console: colour dummy device 80x30
[ 0.000404] Calibrating delay loop (skipped), value calculated using timer frequency.. 1600.00 BogoMIPS (lpj=8000000)
[ 0.000414] pid_max: default: 32768 minimum: 301
[ 0.000509] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000519] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.000917] CPU: Testing write buffer coherency: ok
[ 0.000939] CPU0: Spectre v2: using BPIALL workaround
[ 0.001041] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.001341] Setting up static identity map for 0x100000 - 0x100060
[ 0.001423] mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
[ 0.001511] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001571] rcu: Hierarchical SRCU implementation.
[ 0.001646] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.001708] smp: Bringing up secondary CPUs ...
[ 0.001872] Booting CPU 1
[ 0.002015] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.002022] CPU1: Spectre v2: using BPIALL workaround
[ 0.002081] smp: Brought up 1 node, 2 CPUs
[ 0.002088] SMP: Total of 2 processors activated (3200.00 BogoMIPS).
[ 0.002093] CPU: All CPU(s) started in SVC mode.
[ 0.002453] devtmpfs: initialized
[ 0.004314] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.004366] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.004376] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.004451] pinctrl core: initialized pinctrl subsystem
[ 0.005001] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.005604] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.006058] thermal_sys: Registered thermal governor 'step_wise'
[ 0.006200] cpuidle: using governor ladder
[ 0.006290] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.006297] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.006421] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.006429] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.014955] cryptd: max_cpu_qlen set to 1000
[ 0.015753] raid6: skip pq benchmark and using algorithm neonx8
[ 0.015761] raid6: using neon recovery algorithm
[ 0.016028] SCSI subsystem initialized
[ 0.016108] libata version 3.00 loaded.
[ 0.016197] usbcore: registered new interface driver usbfs
[ 0.016218] usbcore: registered new interface driver hub
[ 0.016236] usbcore: registered new device driver usb
[ 0.016860] clocksource: Switched to clocksource arm_global_timer
[ 0.019111] NET: Registered PF_INET protocol family
[ 0.019224] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.019763] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.019783] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.019793] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.019833] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.019897] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.019946] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.019977] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.020118] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.020138] PCI: CLS 0 bytes, default 64
[ 0.020610] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 0.022525] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.024510] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.024517] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.024966] xor: measuring software checksum speed
[ 0.028802] arm4regs : 2598 MB/sec
[ 0.033729] 8regs : 1998 MB/sec
[ 0.038288] 32regs : 2160 MB/sec
[ 0.043502] neon : 1887 MB/sec
[ 0.043506] xor: using function: arm4regs (2598 MB/sec)
[ 0.043548] bounce: pool size: 64 pages
[ 0.043578] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.044713] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.045254] debugfs: Directory 'f1018100.gpio' with parent 'regmap' already present!
[ 0.045567] debugfs: Directory 'f1018140.gpio' with parent 'regmap' already present!
[ 0.045892] mvebu-pcie soc:pcie: host bridge /soc/pcie ranges:
[ 0.045920] mvebu-pcie soc:pcie: MEM 0x00f1080000..0x00f1081fff -> 0x0000080000
[ 0.045935] mvebu-pcie soc:pcie: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[ 0.045949] mvebu-pcie soc:pcie: MEM 0x00f1044000..0x00f1045fff -> 0x0000044000
[ 0.045963] mvebu-pcie soc:pcie: MEM 0x00f1048000..0x00f1049fff -> 0x0000048000
[ 0.045987] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.046000] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[ 0.046012] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.046024] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0200000000
[ 0.046036] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.046048] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0300000000
[ 0.046060] mvebu-pcie soc:pcie: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.046069] mvebu-pcie soc:pcie: IO 0xffffffffffffffff..0x00fffffffe -> 0x0400000000
[ 0.046167] mvebu-pcie soc:pcie: pcie0.0: Slot power limit 10.0W
[ 0.046223] mvebu-pcie soc:pcie: pcie1.0: Slot power limit 10.0W
[ 0.046274] mvebu-pcie soc:pcie: pcie2.0: Slot power limit 10.0W
[ 0.046823] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 0.046835] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.046845] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf1081fff] (bus address [0x00080000-0x00081fff])
[ 0.046880] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[ 0.046894] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf1045fff] (bus address [0x00044000-0x00045fff])
[ 0.046902] pci_bus 0000:00: root bus resource [mem 0xf1048000-0xf1049fff] (bus address [0x00048000-0x00049fff])
[ 0.046908] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 0.046913] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff]
[ 0.046988] pci 0000:00:01.0: [11ab:6820] type 01 class 0x060400
[ 0.047167] pci 0000:00:02.0: [11ab:6820] type 01 class 0x060400
[ 0.047309] pci 0000:00:03.0: [11ab:6820] type 01 class 0x060400
[ 0.048158] PCI: bus0: Fast back to back transfers disabled
[ 0.048166] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.048177] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.048186] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.049032] PCI: bus1: Fast back to back transfers enabled
[ 0.049039] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.049113] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 0.049135] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 0.049150] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 0.049163] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 0.049235] pci 0000:02:00.0: supports D1 D2
[ 0.049241] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.050137] PCI: bus2: Fast back to back transfers disabled
[ 0.050145] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.050218] pci 0000:03:00.0: [168c:003c] type 00 class 0x028000
[ 0.050240] pci 0000:03:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.050267] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.050338] pci 0000:03:00.0: supports D1 D2
[ 0.051233] PCI: bus3: Fast back to back transfers disabled
[ 0.051240] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
[ 0.051264] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe03fffff]
[ 0.051273] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe07fffff]
[ 0.051281] pci 0000:00:03.0: BAR 8: assigned [mem 0xe0800000-0xe0bfffff]
[ 0.051288] pci 0000:00:01.0: BAR 7: assigned [io 0x10000-0x10fff]
[ 0.051295] pci 0000:00:02.0: BAR 7: assigned [io 0x20000-0x20fff]
[ 0.051301] pci 0000:00:03.0: BAR 7: assigned [io 0x30000-0x30fff]
[ 0.051307] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.051313] pci 0000:00:01.0: bridge window [io 0x10000-0x10fff]
[ 0.051325] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe03fffff]
[ 0.051338] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe04fffff 64bit pref]
[ 0.051351] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0500000-0xe0503fff 64bit pref]
[ 0.051363] pci 0000:02:00.0: BAR 4: assigned [mem 0xe0504000-0xe0504fff 64bit pref]
[ 0.051374] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.051380] pci 0000:00:02.0: bridge window [io 0x20000-0x20fff]
[ 0.051389] pci 0000:00:02.0: bridge window [mem 0xe0400000-0xe07fffff]
[ 0.051401] pci 0000:03:00.0: BAR 0: assigned [mem 0xe0800000-0xe09fffff 64bit]
[ 0.051412] pci 0000:03:00.0: BAR 6: assigned [mem 0xe0a00000-0xe0a0ffff pref]
[ 0.051419] pci 0000:00:03.0: PCI bridge to [bus 03]
[ 0.051424] pci 0000:00:03.0: bridge window [io 0x30000-0x30fff]
[ 0.051433] pci 0000:00:03.0: bridge window [mem 0xe0800000-0xe0bfffff]
[ 0.051499] pcieport 0000:00:01.0: enabling device (0140 -> 0143)
[ 0.051569] pcieport 0000:00:01.0: pciehp: Slot #1 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ IbPresDis- LLActRep+
[ 0.051818] pcieport 0000:00:01.0: pciehp: Slot(1): Card present
[ 0.051875] pcieport 0000:00:02.0: enabling device (0140 -> 0143)
[ 0.051937] pcieport 0000:00:02.0: pciehp: Slot #2 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ IbPresDis- LLActRep+
[ 0.052349] pcieport 0000:00:03.0: enabling device (0140 -> 0143)
[ 0.052406] pcieport 0000:00:03.0: pciehp: Slot #3 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise- Interlock- NoCompl+ IbPresDis- LLActRep+
[ 0.052978] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.066859] mvebu-pcie soc:pcie: pcie2.0: link up
[ 0.066881] mvebu-pcie soc:pcie: pcie1.0: link up
[ 0.107286] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.107425] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.167255] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.167535] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.168854] printk: console [ttyS0] disabled
[ 0.188949] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 30, base_baud = 15625000) is a 16550A
[ 1.472877] printk: console [ttyS0] enabled
[ 1.497557] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 31, base_baud = 15625000) is a 16550A
[ 1.508949] loop: module loaded
[ 1.512110] Loading iSCSI transport class v2.0-870.
[ 1.518135] ahci-mvebu f10a8000.sata: supply ahci not found, using dummy regulator
[ 1.525803] ahci-mvebu f10a8000.sata: supply phy not found, using dummy regulator
[ 1.533349] ahci-mvebu f10a8000.sata: supply target not found, using dummy regulator
[ 1.541192] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 1.550276] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 1.559610] scsi host0: ahci-mvebu
[ 1.563306] scsi host1: ahci-mvebu
[ 1.566793] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 53
[ 1.574749] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 53
[ 1.583720] spi-nor spi0.0: found mx25l6405d, expected s25fl164k
[ 1.589777] spi-nor spi0.0: mx25l6405d (8192 Kbytes)
[ 1.594874] 2 fixed-partitions partitions found on MTD device spi0.0
[ 1.601268] Creating 2 MTD partitions on "spi0.0":
[ 1.606073] 0x000000000000-0x000000100000 : "U-Boot"
[ 1.611345] 0x000000100000-0x000000800000 : "Rescue system"
[ 1.618942] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 1.625948] mvneta_bm f10c8000.bm: Buffer Manager for network controller enabled
[ 1.635007] mvneta f1070000.ethernet eth0: Using hardware mac address d8:58:d7:01:09:30
[ 1.644333] mvneta f1030000.ethernet eth1: Using hardware mac address d8:58:d7:01:09:2e
[ 1.653631] mvneta f1034000.ethernet eth2: Using hardware mac address d8:58:d7:01:09:2f
[ 1.661811] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.668371] ehci-pci: EHCI PCI platform driver
[ 1.672857] ehci-platform: EHCI generic platform driver
[ 1.678186] ehci-orion: EHCI orion driver
[ 1.682298] orion-ehci f1058000.usb: EHCI Host Controller
[ 1.687728] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 1.695363] orion-ehci f1058000.usb: irq 49, io mem 0xf1058000
[ 1.726864] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 1.733105] hub 1-0:1.0: USB hub found
[ 1.736904] hub 1-0:1.0: 1 port detected
[ 1.741260] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.746598] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 1.754174] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 1.763451] xhci-hcd f10f0000.usb3: irq 55, io mem 0xf10f0000
[ 1.769297] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 1.774627] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 1.782174] xhci-hcd f10f0000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.788815] hub 2-0:1.0: USB hub found
[ 1.792590] hub 2-0:1.0: 1 port detected
[ 1.796659] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.804996] hub 3-0:1.0: USB hub found
[ 1.808780] hub 3-0:1.0: 1 port detected
[ 1.812907] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.818255] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.825831] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x0000000000010010
[ 1.835106] xhci-hcd f10f8000.usb3: irq 56, io mem 0xf10f8000
[ 1.840937] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.846266] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.853784] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 1.860397] hub 4-0:1.0: USB hub found
[ 1.864169] hub 4-0:1.0: 1 port detected
[ 1.868240] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.876550] hub 5-0:1.0: USB hub found
[ 1.880330] hub 5-0:1.0: 1 port detected
[ 1.884485] usbcore: registered new interface driver usb-storage
[ 1.891023] armada38x-rtc f10a3800.rtc: registered as rtc0
[ 1.896593] armada38x-rtc f10a3800.rtc: setting system clock to 2022-12-12T03:00:48 UTC (1670814048)
[ 1.905914] i2c_dev: i2c /dev entries driver
[ 1.912471] orion_wdt: Initial timeout 171 sec
[ 1.913058] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.917183] sdhci: Secure Digital Host Controller Interface driver
[ 1.928562] sdhci: Copyright(c) Pierre Ossman
[ 1.933038] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.939686] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.947366] NET: Registered PF_INET6 protocol family
[ 1.952968] Segment Routing with IPv6
[ 1.956661] In-situ OAM (IOAM) with IPv6
[ 1.960659] NET: Registered PF_PACKET protocol family
[ 1.965010] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 1.965758] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.986243] 8021q: 802.1Q VLAN Support v1.8
[ 1.990556] Registering SWP/SWPB emulation handler
[ 1.997608] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[ 2.101993] mmc0: new high speed MMC card at address 0001
[ 2.107763] mmcblk0: mmc0:0001 008G30 7.28 GiB
[ 2.113634] mmcblk0: p1
[ 2.116471] mmcblk0boot0: mmc0:0001 008G30 4.00 MiB
[ 2.121893] mmcblk0boot1: mmc0:0001 008G30 4.00 MiB
[ 2.127146] mmcblk0rpmb: mmc0:0001 008G30 4.00 MiB, chardev (247:0)
[ 2.966863] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.973130] ata1.00: ATA-9: GTA 256GB SSD, HCS1A25C, max UDMA/133
[ 2.979250] ata1.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 32)
[ 2.986773] ata1.00: configured for UDMA/133
[ 2.991244] scsi 0:0:0:0: Direct-Access ATA GTA 256GB SSD A25C PQ: 0 ANSI: 5
[ 2.999803] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[ 3.007350] sd 0:0:0:0: [sda] Write Protect is off
[ 3.012155] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.012190] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.022240] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 3.029345] squashfs: Unknown parameter 'commit'
[ 3.035028] F2FS-fs (mmcblk0p1): Magic Mismatch, valid(0xf2f52010) - read(0x0)
[ 3.042285] F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 1th superblock
[ 3.050968] F2FS-fs (mmcblk0p1): Magic Mismatch, valid(0xf2f52010) - read(0x0)
[ 3.058220] F2FS-fs (mmcblk0p1): Can't find valid F2FS filesystem in 2th superblock
[ 3.066898] BTRFS: device fsid ec715b08-b0a6-4fb2-aca1-07df948ffd7a devid 1 transid 2787793 /dev/root scanned by swapper/0 (1)
[ 3.079709] BTRFS info (device mmcblk0p1): disk space caching is enabled
[ 3.086432] BTRFS info (device mmcblk0p1): has skinny extents
[ 3.112892] BTRFS info (device mmcblk0p1): enabling ssd optimizations
[ 3.126232] VFS: Mounted root (btrfs filesystem) on device 0:14.
[ 3.133909] devtmpfs: mounted
[ 3.137325] Freeing unused kernel image (initmem) memory: 1024K
[ 3.177017] Run /sbin/init as init process
[ 3.181124] with arguments:
[ 3.181126] /sbin/init
[ 3.181128] earlyprintk
[ 3.181130] with environment:
[ 3.181132] HOME=/
[ 3.181134] TERM=linux
[ 3.181136] mangled_fs=btrfs
[ 3.219493] init: Console is alive
[ 3.222994] init: - watchdog -
[ 3.296885] pcieport 0000:00:01.0: pciehp: Slot(1): No link
[ 3.519262] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.534425] Key type encrypted registered
[ 3.541185] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com
[ 3.552150] ehci-fsl: Freescale EHCI Host controller driver
[ 3.559258] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.565862] ohci-platform: OHCI generic platform driver
[ 3.575434] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.582303] ohci-pci: OHCI PCI platform driver
[ 3.588666] usbcore: registered new interface driver uas
[ 3.594123] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.604194] init: - preinit -
[ 5.713755] mount_root: mounting /dev/root
[ 5.720128] mount_root: loading kmods from internal overlay
[ 5.738236] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 5.746152] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 6.414082] block: attempting to load /etc/config/fstab
[ 6.421879] block: extroot: not configured
[ 6.445681] urandom-seed: Seeding with /etc/urandom.seed
[ 6.808721] BTRFS: device label srv devid 1 transid 50797 /dev/sda scanned by btrfs (625)
[ 6.817026] BTRFS info: devid 1 device path /dev/root changed to /dev/mmcblk0p1 scanned by btrfs (625)
[ 6.828992] procd: - early -
[ 6.831911] procd: - watchdog -
[ 7.361619] procd: - watchdog -
[ 7.364984] procd: - ubus -
[ 7.374276] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.417240] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.423738] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.430898] procd: - init -
[ 7.795316] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.862901] Key type dns_resolver registered
[ 7.872624] RPC: Registered named UNIX socket transport module.
[ 7.878600] RPC: Registered udp transport module.
[ 7.883318] RPC: Registered tcp transport module.
[ 7.888036] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.901273] tun: Universal TUN/TAP device driver, 1.6
[ 7.912572] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 7.926561] mv88e6085 f1072004.mdio-mii:10: switch 0x1760 detected: Marvell 88E6176, revision 1
[ 8.079971] random: crng init done
[ 8.083395] random: 23 urandom warning(s) missed due to ratelimiting
[ 8.997155] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 9.007059] mv88e6085 f1072004.mdio-mii:10: configuring for fixed/rgmii-id link mode
[ 9.016454] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 9.025365] mv88e6085 f1072004.mdio-mii:10: Link is Up - 1Gbps/Full - flow control off
[ 9.129145] mv88e6085 f1072004.mdio-mii:10 lan0 (uninitialized): PHY [mv88e6xxx-0:00] driver [Marvell 88E1540] (irq=79)
[ 9.240740] mv88e6085 f1072004.mdio-mii:10 lan1 (uninitialized): PHY [mv88e6xxx-0:01] driver [Marvell 88E1540] (irq=80)
[ 9.357204] mv88e6085 f1072004.mdio-mii:10 lan2 (uninitialized): PHY [mv88e6xxx-0:02] driver [Marvell 88E1540] (irq=81)
[ 9.476993] mv88e6085 f1072004.mdio-mii:10 lan3 (uninitialized): PHY [mv88e6xxx-0:03] driver [Marvell 88E1540] (irq=82)
[ 9.592029] mv88e6085 f1072004.mdio-mii:10 lan4 (uninitialized): PHY [mv88e6xxx-0:04] driver [Marvell 88E1540] (irq=83)
[ 9.608181] DSA: tree 0 setup
[ 9.623331] NFS: Registering the id_resolver key type
[ 9.628475] Key type id_resolver registered
[ 9.632676] Key type id_legacy registered
[ 9.686422] i2c i2c-0: Added multiplexed i2c bus 1
[ 9.691420] i2c i2c-0: Added multiplexed i2c bus 2
[ 9.696383] i2c i2c-0: Added multiplexed i2c bus 3
[ 9.701518] i2c i2c-0: Added multiplexed i2c bus 4
[ 9.706626] i2c i2c-0: Added multiplexed i2c bus 5
[ 9.715721] i2c i2c-0: Added multiplexed i2c bus 6
[ 9.720808] i2c i2c-0: Added multiplexed i2c bus 7
[ 9.726282] pca953x 8-0071: supply vcc not found, using dummy regulator
[ 9.733125] pca953x 8-0071: using no AI
[ 9.740823] i2c i2c-0: Added multiplexed i2c bus 8
[ 9.745658] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547
[ 9.754270] sfp sfp: Host maximum power 3.0W
[ 9.754886] GACT probability on
[ 9.762343] Mirror/redirect action on
[ 9.769931] u32 classifier
[ 9.772662] input device check on
[ 9.776341] Actions configured
[ 9.785039] fuse: init (API version 7.34)
[ 9.793212] at24 1-0054: supply vcc not found, using dummy regulator
[ 9.804318] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
[ 9.811902] Bridge firewalling registered
[ 9.821868] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[ 9.829497] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[ 9.855383] usbcore: registered new interface driver ums-alauda
[ 9.861840] usbcore: registered new interface driver ums-cypress
[ 9.868565] usbcore: registered new interface driver ums-datafab
[ 9.875109] usbcore: registered new interface driver ums-freecom
[ 9.881705] usbcore: registered new interface driver ums-isd200
[ 9.892342] usbcore: registered new interface driver ums-jumpshot
[ 9.899177] usbcore: registered new interface driver ums-karma
[ 9.905774] usbcore: registered new interface driver ums-sddr09
[ 9.912374] usbcore: registered new interface driver ums-sddr55
[ 9.919025] usbcore: registered new interface driver ums-usbat
[ 9.926107] usbcore: registered new interface driver usbserial_generic
[ 9.932719] usbserial: USB Serial support registered for generic
[ 9.954187] xt_time: kernel timezone is -0000
[ 9.989459] mt7915e 0000:02:00.0: enabling device (0140 -> 0142)
[ 10.098172] sfp sfp: module ODI DFP-34X-2C2 rev sn XPON22100614 dc 221009
[ 10.107541] mvneta f1034000.ethernet eth2: switched to inband/1000base-x link mode
[ 10.132855] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a
[ 10.132855]
[ 10.168508] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052
[ 10.196071] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111
[ 10.354933] PPP generic driver version 2.4.2
[ 10.360192] NET: Registered PF_PPPOX protocol family
[ 10.367669] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 10.375530] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 10.399272] ath10k_pci 0000:03:00.0: enabling device (0140 -> 0142)
[ 10.405758] ath10k_pci 0000:03:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 10.660499] ath10k_pci 0000:03:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 10.669776] ath10k_pci 0000:03:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 10.679409] ath10k_pci 0000:03:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[ 10.736708] ath10k_pci 0000:03:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 11.876556] ath10k_pci 0000:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 11.998290] ath: EEPROM regdomain: 0x0
[ 11.998299] ath: EEPROM indicates default country code should be used
[ 11.998301] ath: doing EEPROM country->regdmn map search
[ 11.998305] ath: country maps to regdmn code: 0x3a
[ 11.998308] ath: Country alpha2 being used: US
[ 11.998311] ath: Regpair used: 0x3a
[ 15.657664] usbcore: registered new interface driver qcserial
[ 15.663462] usbserial: USB Serial support registered for Qualcomm USB modem
[ 15.676783] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 18.465949] mvneta f1030000.ethernet eth1: configuring for fixed/rgmii link mode
[ 18.474095] mvneta f1030000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 18.482206] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 18.489378] mv88e6085 f1072004.mdio-mii:10 lan0: configuring for phy/gmii link mode
[ 18.502497] br-lan: port 1(lan0) entered blocking state
[ 18.507784] br-lan: port 1(lan0) entered disabled state
[ 18.564099] device lan0 entered promiscuous mode
[ 18.568772] device eth1 entered promiscuous mode
[ 18.741017] mv88e6085 f1072004.mdio-mii:10 lan1: configuring for phy/gmii link mode
[ 18.796955] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 18.865008] br-lan: port 2(lan1) entered blocking state
[ 18.865927] mv88e6085 f1072004.mdio-mii:10 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 18.870263] br-lan: port 2(lan1) entered disabled state
[ 18.932264] device lan1 entered promiscuous mode
[ 19.150136] mv88e6085 f1072004.mdio-mii:10 lan2: configuring for phy/gmii link mode
[ 19.190118] br-lan: port 1(lan0) entered blocking state
[ 19.195376] br-lan: port 1(lan0) entered forwarding state
[ 19.217202] br-lan: port 2(lan1) entered blocking state
[ 19.222458] br-lan: port 2(lan1) entered forwarding state
[ 19.241487] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.266844] BTRFS info (device sda): disk space caching is enabled
[ 19.273071] BTRFS info (device sda): has skinny extents
[ 19.303442] BTRFS info (device sda): enabling ssd optimizations
[ 19.371538] br-lan: port 3(lan2) entered blocking state
[ 19.376790] br-lan: port 3(lan2) entered disabled state
[ 19.402155] mv88e6085 f1072004.mdio-mii:10 lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 19.983748] device lan2 entered promiscuous mode
[ 20.012570] br-lan: port 3(lan2) entered blocking state
[ 20.017843] br-lan: port 3(lan2) entered forwarding state
[ 20.026829] mv88e6085 f1072004.mdio-mii:10 lan3: configuring for phy/gmii link mode
[ 20.098417] br-lan: port 4(lan3) entered blocking state
[ 20.103680] br-lan: port 4(lan3) entered disabled state
[ 20.170789] device lan3 entered promiscuous mode
[ 20.202401] mv88e6085 f1072004.mdio-mii:10 lan4: configuring for phy/gmii link mode
[ 20.277152] br-lan: port 5(lan4) entered blocking state
[ 20.282411] br-lan: port 5(lan4) entered disabled state
[ 20.344113] device lan4 entered promiscuous mode
[ 20.383151] mvneta f1034000.ethernet eth2: configuring for inband/1000base-x link mode
[ 20.446951] mvneta f1034000.ethernet eth2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 20.455012] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 20.461525] IPv6: ADDRCONF(NETDEV_CHANGE): eth2.2000: link becomes ready
[ 27.350234] process '@/usr/bin/zerotier-one' started with executable stack
[ 29.470689] br-lan: port 6(vethIsxPBP) entered blocking state
[ 29.476468] br-lan: port 6(vethIsxPBP) entered disabled state
[ 29.482472] device vethIsxPBP entered promiscuous mode
[ 29.520713] eth0: renamed from veth1g5b7M
[ 29.558102] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.564552] IPv6: ADDRCONF(NETDEV_CHANGE): vethIsxPBP: link becomes ready
[ 29.571568] br-lan: port 6(vethIsxPBP) entered blocking state
[ 29.577361] br-lan: port 6(vethIsxPBP) entered forwarding state
[ 29.878858] br-lan: port 7(vethzdk0fh) entered blocking state
[ 29.884639] br-lan: port 7(vethzdk0fh) entered disabled state
[ 29.890634] device vethzdk0fh entered promiscuous mode
[ 29.937707] br-lan: port 7(vethzdk0fh) entered blocking state
[ 29.943490] br-lan: port 7(vethzdk0fh) entered forwarding state
[ 29.978309] eth0: renamed from veth7OaZlz
[ 30.050915] IPv6: ADDRCONF(NETDEV_CHANGE): vethzdk0fh: link becomes ready
[ 30.851636] pppoe-wan: renamed from ppp0
[ 43.826279] docker0: port 1(veth6250cc1) entered blocking state
[ 43.832290] docker0: port 1(veth6250cc1) entered disabled state
[ 43.838449] device veth6250cc1 entered promiscuous mode
[ 46.423556] eth0: renamed from veth4330730
[ 46.481672] IPv6: ADDRCONF(NETDEV_CHANGE): veth6250cc1: link becomes ready
[ 46.489874] docker0: port 1(veth6250cc1) entered blocking state
[ 46.495821] docker0: port 1(veth6250cc1) entered forwarding state
[ 46.529298] IPv6: ADDRCONF(NETDEV_CHANGE): docker0: link becomes ready
[ 66.794991] TCP: request_sock_TCP: Possible SYN flooding on port 5000. Sending cookies. Check SNMP counters.
[ 94.469869] docker0: port 1(veth6250cc1) entered disabled state
[ 94.476427] veth4330730: renamed from eth0
[ 94.591912] docker0: port 1(veth6250cc1) entered disabled state
[ 94.600511] device veth6250cc1 left promiscuous mode
[ 94.605518] docker0: port 1(veth6250cc1) entered disabled state
[ 94.800585] docker0: port 1(veth23868d8) entered blocking state
[ 94.806562] docker0: port 1(veth23868d8) entered disabled state
[ 94.812777] device veth23868d8 entered promiscuous mode
[ 94.820955] docker0: port 1(veth23868d8) entered blocking state
[ 94.826942] docker0: port 1(veth23868d8) entered forwarding state
[ 95.553352] docker0: port 1(veth23868d8) entered disabled state
[ 95.703530] eth0: renamed from veth87afa25
[ 95.743873] IPv6: ADDRCONF(NETDEV_CHANGE): veth23868d8: link becomes ready
[ 95.750941] docker0: port 1(veth23868d8) entered blocking state
[ 95.756906] docker0: port 1(veth23868d8) entered forwarding state
[ 106.072583] TCP: request_sock_TCPv6: Possible SYN flooding on port 5000. Sending cookies. Check SNMP counters.
[ 3588.663946] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead.
[44408.831180] br-lan: port 1(lan0) entered disabled state
[44408.837260] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Down
[44434.230309] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
[44434.238937] br-lan: port 1(lan0) entered blocking state
[44434.244183] br-lan: port 1(lan0) entered forwarding state
[47703.771367] pppoe-wan: renamed from ppp0
[47738.040041] docker0: port 1(veth23868d8) entered disabled state
[47738.048085] veth87afa25: renamed from eth0
[47738.166507] docker0: port 1(veth23868d8) entered disabled state
[47738.175657] device veth23868d8 left promiscuous mode
[47738.180720] docker0: port 1(veth23868d8) entered disabled state
[47738.364785] docker0: port 1(vethfb1e356) entered blocking state
[47738.370793] docker0: port 1(vethfb1e356) entered disabled state
[47738.376993] device vethfb1e356 entered promiscuous mode
[47738.384386] docker0: port 1(vethfb1e356) entered blocking state
[47738.390374] docker0: port 1(vethfb1e356) entered forwarding state
[47739.065556] docker0: port 1(vethfb1e356) entered disabled state
[47739.326272] eth0: renamed from veth0a77a23
[47739.366345] IPv6: ADDRCONF(NETDEV_CHANGE): vethfb1e356: link becomes ready
[47739.373379] docker0: port 1(vethfb1e356) entered blocking state
[47739.379340] docker0: port 1(vethfb1e356) entered forwarding state
[86348.391702] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Down
[86348.422739] br-lan: port 1(lan0) entered disabled state
[86365.861397] mv88e6085 f1072004.mdio-mii:10 lan0: Link is Up - 1Gbps/Full - flow control rx/tx
[86365.870014] br-lan: port 1(lan0) entered blocking state
[86365.875277] br-lan: port 1(lan0) entered forwarding state
I also cannot force it, by disabling auto negotiation:
root@turris:~# ethtool -s eth2 autoneg off speed 2500 duplex half
Cannot set new settings: Invalid argument
not setting speed
not setting duplex
not setting autoneg
root@turris:~# ethtool -s eth2 autoneg off
Cannot set new settings: Invalid argument
not setting autoneg
root@turris:~# ethtool -s eth2 speed 2500 duplex half
Cannot advertise speed 2500 duplex half
root@turris:~# ethtool -s eth2 speed 2500
Cannot advertise speed 2500
Is there anything I can do, or 1Gbps is the maximum throughput I can have with this setup?