Při změnách nastavení (změny přidělování fixních IP) se první poškodilo uložené nastavení vazeb IP na MAC a nezobrazilo se to co jsem uložil a potom mi router přestal přidělovat IP adresy … tzn. byl nedostupný pro terminál a schnapps. Použití záchrany tlačítkem 1-4 LED se systémem na SSD disku není možné …
Dnes jsem se odhodlal k reflash systému pomocí seriové linky na poslední medkit 4.xx
Operace proběhla poměrně hladce … tzn. rescueboot jsem spustil a postupoval podle návodu https://wiki.turris.cz/doc/cs/howto/omnia_booting_from_external_storage … ALE příkaz boot nevedl ke spuštění systému routeru.
Zkusil znovu vstoupit do rescueboot a proces opakovat. Rescueboot přejde do startu routeru (pokud to čtu dobře) ale ten je zacyklovaný.
run rescueboot
Error writing the chip: 21504024
Error writing the chip: 21504024
Error writing the chip: 21504024
SF: Detected S25FL164K with page size 256 Bytes, erase size 64 KiB, total 8 MiB
device 0 offset 0x100000, size 0x700000
SF: 7340032 bytes @ 0x100000 Read: OK
Kernel image @ 0x1000000 [ 0x000000 - 0x689b30 ]
Souhrn
Starting kernel ...
<00>
U-Boot SPL 2015.10-rc2 (Aug 18 2016 - 20:43:35)
High speed PHY - Version: 2.0
SERDES0 card detect: SATA
Initialize Turris board topology
Detected Device ID 6820
board SerDes lanes topology details:
| Lane # | Speed | Type |
--------------------------------
| 0 | 6 | SATA0 |
| 1 | 5 | USB3 HOST0 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
--------------------------------
poll_op_execute: TIMEOUT
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
:** Link is Gen1, check the EP capability
PCIe, Idx 2: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.29.0
Memory config in EEPROM: 0x01
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
U-Boot 2015.10-rc2 (Aug 18 2016 - 20:43:35 +0200), Build: jenkins-omnia-master-23
SoC: MV88F6820-A0
Watchdog enabled
I2C: ready
SPI: ready
DRAM: 1 GiB (ECC not enabled)
Enabling Armada 385 watchdog.
Disabling MCU startup watchdog.
Regdomain set to **
MMC: mv_sdh: 0
SF: Detected S25FL164K with page size 256 Bytes, erase size 64 KiB, total 8 MiB
PCI:
00:01.0 - 168c:003c - Network controller
PCI:
01:00.0 - 11ab:6820 - Memory controller
01:01.0 - 168c:002e - Network controller
Model: Marvell Armada 385 GP
Board: Turris Omnia SN: 0000000B00006219
Regdomain set to **
SCSI: MVEBU SATA INIT
Target spinup took 0 ms.
SATA link 1 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
Net: neta2
Hit any key to stop autoboot: 0
Setting bus to 1
BOOT eMMC FS
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: KINGSTON SUV500M Rev: 0030
Type: Hard Disk
Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
Found 1 device(s).
BtrFS init: Max node or leaf size 16384
3351944 bytes read in 134 ms (23.9 MiB/s)
BtrFS init: Max node or leaf size 16384
18773 bytes read in 108 ms (168.9 KiB/s)
Kernel image @ 0x1000000 [ 0x000000 - 0x332588 ]
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Loading Device Tree to 0fff8000, end 0ffff954 ... OK
Starting kernel ...
<00>
U-Boot SPL 2015.10-rc2 (Aug 18 2016 - 20:43:35)
High speed PHY - Version: 2.0
SERDES0 card detect: SATA
Spuštení samotného routeru probíhá stejně tzn. je zacyklené.
<00><00>
U-Boot SPL 2015.10-rc2 (Aug 18 2016 - 20:43:35)
High speed PHY - Version: 2.0
SERDES0 card detect: SATA
Initialize Turris board topology
Detected Device ID 6820
board SerDes lanes topology details:
Souhrn
| Lane # | Speed | Type |
--------------------------------
| 0 | 6 | SATA0 |
| 1 | 5 | USB3 HOST0 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
--------------------------------
poll_op_execute: TIMEOUT
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
:** Link is Gen1, check the EP capability
PCIe, Idx 2: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.29.0
Memory config in EEPROM: 0x01
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
U-Boot 2015.10-rc2 (Aug 18 2016 - 20:43:35 +0200), Build: jenkins-omnia-master-23
SoC: MV88F6820-A0
Watchdog enabled
I2C: ready
SPI: ready
DRAM: 1 GiB (ECC not enabled)
Enabling Armada 385 watchdog.
Disabling MCU startup watchdog.
Regdomain set to **
MMC: mv_sdh: 0
SF: Detected S25FL164K with page size 256 Bytes, erase size 64 KiB, total 8 MiB
PCI:
00:01.0 - 168c:003c - Network controller
PCI:
01:00.0 - 11ab:6820 - Memory controller
01:01.0 - 168c:002e - Network controller
Model: Marvell Armada 385 GP
Board: Turris Omnia SN: 0000000B00006219
Regdomain set to **
SCSI: MVEBU SATA INIT
Target spinup took 0 ms.
SATA link 1 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
Net: neta2
Hit any key to stop autoboot: 0
Setting bus to 1
BOOT eMMC FS
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: KINGSTON SUV500M Rev: 0030
Type: Hard Disk
Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
Found 1 device(s).
BtrFS init: Max node or leaf size 16384
3351944 bytes read in 157 ms (20.4 MiB/s)
BtrFS init: Max node or leaf size 16384
18773 bytes read in 108 ms (168.9 KiB/s)
Kernel image @ 0x1000000 [ 0x000000 - 0x332588 ]
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
Loading Device Tree to 0fff8000, end 0ffff954 ... OK
Starting kernel ...
<00>
U-Boot SPL 2015.10-rc2 (Aug 18 2016 - 20:43:35)
High speed PHY - Version: 2.0
SERDES0 card detect: SATA
Občas … ale ne vždy ohlásí:
=> run rescueboot
Error writing the chip: 21504024
Error writing the chip: 21504024
Error writing the chip: 21504024
SF: Detected S25FL164K with page size 256 Bytes, erase size 64 KiB, total 8 MiB
device 0 offset 0x100000, size 0x700000
SF: 7340032 bytes @ 0x100000 Read: OK
Kernel image @ 0x1000000 [ 0x000000 - 0x689b30 ]
Starting kernel ...
Mám dojem, že přístroj (květen 2016) definitivně zemřel … mohu s klidným svědomím prohlásit R.I.P. ?