Omnia 3.10 disappeared Wi-Fi


#7

Hi guys!

I have a similar problem. After the update to 3.10 my 2Ghz card (R11e-2HPnD) and my SATA disk are gone. Both are no longer accessible in the system and also can no longer be found via lspci.

root@turris:~# lspci -v
00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: fast devsel
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00
lspci: Unable to load libkmod resources: error -12

00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Memory behind bridge: e0000000-e02fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00

00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: fast devsel
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00

02:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
	Subsystem: Device 19b6:d03c
	Flags: bus master, fast devsel, latency 0, IRQ 119
	Memory at e0000000 (64-bit, non-prefetchable) [size=2M]
	Expansion ROM at e0200000 [disabled] [size=64K]
	Capabilities: [40] Power Management version 2
	Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
	Capabilities: [70] Express Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
	Kernel driver in use: ath10k_pci

With a MEDKIT-reset, we were back. After a reboot, however, the problem occurs again. What happened during the update? There is something wrong with the PCI ports now!

It’s a Omnia 2GB device.

What can we do?


#8

The problem suspected in this topic is not global PCI problem but rather problem with single card and its single revision. Because of that I suspect that you have different problem.

Please reboot your device and post output from dmesg (as soon as possible after reboot). That should give us better understanding what is happening in your case. But I suspect that your problem is rather missing firmware or kernel driver. So could you also check what packages are being removed when you update to Turris 3.10?


#9

Not sure if I have the same issue, but I have the same symptoms. Well, except 5GHz wlan is still visible on lspci output.
“Solution” I am using is either several reboots (so long until ath10k_pci start to work) or power off and power on again.

dmesg part when ath10_pci works
...
[   19.382148] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   19.388012] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   19.564548] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   19.575291] ath10k_pci 0000:02:00.0: Falling back to user helper
[   19.594116] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   19.604510] ath10k_pci 0000:02:00.0: Falling back to user helper
[   19.630781] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   19.640069] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   19.649668] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   19.694424] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[   19.701542] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   19.712013] ath10k_pci 0000:02:00.0: Falling back to user helper
[   19.730675] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   20.859737] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
...
dmesg part when ath10_pci doesn't work
...
[   21.492221] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   21.497910] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[   21.504390] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   21.684599] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   21.695336] ath10k_pci 0000:02:00.0: Falling back to user helper
[   21.714164] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   21.724552] ath10k_pci 0000:02:00.0: Falling back to user helper
[   21.750760] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   21.760039] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   21.769634] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   21.814366] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[   21.821483] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   21.831948] ath10k_pci 0000:02:00.0: Falling back to user helper
[   21.850549] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   23.950927] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[   24.950923] ath10k_pci 0000:02:00.0: Service connect timeout
[   24.956596] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[   25.041278] ath10k_pci 0000:02:00.0: could not init core (-110)
[   25.047233] ath10k_pci 0000:02:00.0: could not probe fw (-110)
...

Cards are mounted:


#10

Our experience is that WiFi cards are pretty hot, so in your case, there are two solutions.

  1. Put the heatsink on 5 GHz card and see if it helps for you
  2. If you live in Prague I can pick up your router and give it to our HW guys and they will change the capacitors or you can send it to us.

#11

Sent PM

(Lorem ipsum)


#12

i reboot my router and now the 5Ghz Wifi is on again.


#13

Is there any possible to check, if 5Ghz card is faulty? From serial number or such? I have indiegogo 2GB + Wifi perk :disappointed_relieved:, but I deinstall 5Ghz card from the start (even before first plug I think), because I dont need it yet (and not all my devices supports 5Ghz)…

Btw., I think its strange that those problems appears to some users after 3.10 update, at least it seems to me that way.


#14

@Jan.H should know serial numbers. It’s also somewhere here on forum. It’s about a year old problem.

Problem with it is that it’s caused by interference on board. That specific card has fault where it’s more prone to be affected by it. Two right slots share reference time and if one of cards generates some noise then it can affect second card if it doesn’t have sufficient filtering. Real problem is that this noise don’t have to be just from second card but also from other sources. So this can start happening just because you moved router to some spot with just right problematic interference. That is why it propagates dynamically. But it might not ever show. All boards propagating given error are requested to be sent to us for repair (as pepe wrote, capacitors change). It makes no sense to recall all routers because most of them wont encounter problem because it really depends on combination of factors. In my case for example it manifested when I tried to move a lot of data to drive (connected using SATA card). I swapped ac and g cards, ac being in left most port and since then I had no problems. But we failed to reproduce it for example with msata or other cards.
As you can see there is no guaranteed way to ensure that it won’t happen or that it happens. That capacitors replacement is more or less just hack to overcome this specific problem but when some card misbehaves then there is nothing hardware designer can do.

And why it seems to be problematic with 3.10? I don’t think that it’s. But even if it would then it’s possible that some software change just makes it more inclined to this problem. But I currently know only about one person that started having problems after 3.10. Other one in this topic encounters problems for longer time period. And I don’t know about anyone else.


mPCIe slots and 802.11AC wave 2
#15

So, now from me three different dmesg outputs I have generated today. The behavior of the Omnia is currently not reproducible. Problems definitely occurred since the weekend and after the update to 3.10. Everything was stable before.

I really need assistance here!

a) All cards work (mSATA, 802.11n, 802.11ac)

[    7.023204] BTRFS info (device mmcblk0p1): disk space caching is enabled
[    7.029922] BTRFS: has skinny extents
[    7.038110] BTRFS: detected SSD devices, enabling SSD mode
[    7.080924] VFS: Mounted root (btrfs filesystem) on device 0:13.
[    7.087071] Freeing unused kernel memory: 284K
[    7.139262] init: Console is alive
[    7.142757] init: - watchdog -
[    7.495863] usbcore: registered new interface driver usbfs
[    7.501405] usbcore: registered new interface driver hub
[    7.506762] usbcore: registered new device driver usb
[    7.513655] exFAT: Version 1.2.9
[    7.531226] JFS: nTxBlock = 8192, nTxLock = 65536
[    7.592013] SGI XFS with security attributes, no debug enabled
[    7.599467] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.606394] ehci-platform: EHCI generic platform driver
[    7.612027] ehci-orion: EHCI orion driver
[    7.616149] orion-ehci f1058000.usb: EHCI Host Controller
[    7.621592] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    7.629238] orion-ehci f1058000.usb: irq 39, io mem 0xf1058000
[    7.650913] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    7.657109] hub 1-0:1.0: USB hub found
[    7.660883] hub 1-0:1.0: 1 port detected
[    7.665889] uhci_hcd: USB Universal Host Controller Interface driver
[    7.675395] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.680730] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    7.688352] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.696928] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[    7.702948] hub 2-0:1.0: USB hub found
[    7.706718] hub 2-0:1.0: 1 port detected
[    7.710743] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.716086] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    7.723649] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.731974] hub 3-0:1.0: USB hub found
[    7.735744] hub 3-0:1.0: 1 port detected
[    7.739817] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.745165] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    7.752762] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.761334] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[    7.767329] hub 4-0:1.0: USB hub found
[    7.771112] hub 4-0:1.0: 1 port detected
[    7.775129] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.780457] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    7.788001] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.796320] hub 5-0:1.0: USB hub found
[    7.800089] hub 5-0:1.0: 1 port detected
[    7.805274] usbcore: registered new interface driver usb-storage
[    8.146068] init: - preinit -
[   11.196996] mount_root: mounting /dev/root
[   11.202070] BTRFS info (device mmcblk0p1): disk space caching is enabled
[   11.209425] mount_root: loading kmods from internal overlay
[   11.421937] block: attempting to load /etc/config/fstab
[   11.428010] block: extroot: not configured
[   11.434510] procd: - early -
[   11.437417] procd: - watchdog -
[   11.535556] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.562042] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.597415] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.622019] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.657747] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.682580] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.718049] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.742693] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.778356] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.803123] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   12.003934] procd: - ubus -
[   13.009282] procd: - init -
[   13.067310] marvell-cesa f1090000.crypto: CESA device successfully registered
[   13.080379] NET: Registered protocol family 38
[   13.096152] md: linear personality registered for level -1
[   13.102051] md: raid0 personality registered for level 0
[   13.108075] md: raid1 personality registered for level 1
[   13.114497] md: raid10 personality registered for level 10
[   13.120362] async_tx: api initialized (async)
[   13.127741] md: raid6 personality registered for level 6
[   13.133092] md: raid5 personality registered for level 5
[   13.138415] md: raid4 personality registered for level 4
[   13.145598] FS-Cache: Loaded
[   13.148918] md: multipath personality registered for level -4
[   13.155873] NET: Registered protocol family 8
[   13.160241] NET: Registered protocol family 20
[   13.168435] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[   13.179265] Key type dns_resolver registered
[   13.186401] NET: Registered protocol family 33
[   13.190858] Key type rxrpc registered
[   13.194548] Key type rxrpc_s registered
[   13.201568] kAFS: Red Hat AFS client v0.1 registering.
[   13.206752] FS-Cache: Netfs 'afs' registered for caching
[   13.241298] RPC: Registered named UNIX socket transport module.
[   13.247236] RPC: Registered udp transport module.
[   13.251976] RPC: Registered tcp transport module.
[   13.256688] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.281093] NFS: Registering the id_resolver key type
[   13.286177] Key type id_resolver registered
[   13.290369] Key type id_legacy registered
[   13.295015] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   13.304261] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   13.314102] RxRPC: Registered security type 2 'rxkad'
[   13.330646] tun: Universal TUN/TAP device driver, 1.6
[   13.335747] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.345563] sit: IPv6 over IPv4 tunneling driver
[   13.352368] gre: GRE over IPv4 demultiplexor driver
[   13.357884] ip_gre: GRE over IPv4 tunneling driver
[   13.377756] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   13.386411] PPP generic driver version 2.4.2
[   13.393984] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.404326] cryptodev: driver 1.8 loaded.
[   13.412155] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   13.420181] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   13.496993] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   13.502892] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.684394] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   13.695128] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.704892] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.714022] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   13.724408] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.733969] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.750648] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 19b6:d03c
[   13.759920] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.769447] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   13.814197] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[   13.821313] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.831779] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.841518] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.850446] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.977243] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   15.061356] ath: EEPROM regdomain: 0x0
[   15.061361] ath: EEPROM indicates default country code should be used
[   15.061364] ath: doing EEPROM country->regdmn map search
[   15.061368] ath: country maps to regdmn code: 0x3a
[   15.061371] ath: Country alpha2 being used: US
[   15.061374] ath: Regpair used: 0x3a
[   15.067002] u32 classifier
[   15.069725]     input device check on
[   15.073414]     Actions configured
[   15.077493] Mirror/redirect action on
[   15.082315] GACT probability on
[   15.089875] netem: version 1.3
[   15.098088] fuse init (API version 7.23)
[   15.113858] usbcore: registered new interface driver cdc_wdm
[   15.122498] Ebtables v2.0 registered
[   15.127444] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.139339] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   15.304263] Netfilter messages via NETLINK v0.30.
[   15.309819] PPP MPPE Compression module registered
[   15.315162] NET: Registered protocol family 24
[   15.323029] usbcore: registered new interface driver ums-alauda
[   15.329706] usbcore: registered new interface driver ums-cypress
[   15.336637] usbcore: registered new interface driver ums-datafab
[   15.343454] usbcore: registered new interface driver ums-freecom
[   15.350328] usbcore: registered new interface driver ums-isd200
[   15.357277] usbcore: registered new interface driver ums-jumpshot
[   15.364191] usbcore: registered new interface driver ums-karma
[   15.371232] usbcore: registered new interface driver ums-sddr09
[   15.378054] usbcore: registered new interface driver ums-sddr55
[   15.385013] usbcore: registered new interface driver ums-usbat
[   15.396775] usbcore: registered new interface driver usbserial
[   15.402662] usbcore: registered new interface driver usbserial_generic
[   15.409229] usbserial: USB Serial support registered for generic
[   15.424055] xt_time: kernel timezone is -0000
[   15.442275] usbcore: registered new interface driver cdc_ether
[   15.452663] ctnetlink v0.93: registering with nfnetlink.
[   15.461620] usbcore: registered new interface driver qmi_wwan
[   15.468556] usbcore: registered new interface driver rndis_host
[   15.482089] pci 0000:00:03.0: enabling device (0140 -> 0142)
[   15.494132] ath: EEPROM regdomain: 0x0
[   15.494136] ath: EEPROM indicates default country code should be used
[   15.494139] ath: doing EEPROM country->regdmn map search
[   15.494143] ath: country maps to regdmn code: 0x3a
[   15.494146] ath: Country alpha2 being used: US
[   15.494149] ath: Regpair used: 0x3a
[   15.500943] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   15.502336] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xf1d40000, irq=109
[   15.510833] usbcore: registered new interface driver option
[   15.516486] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.524151] usbcore: registered new interface driver qcserial
[   15.529940] usbserial: USB Serial support registered for Qualcomm USB modem
[   18.403937] random: nonblocking pool is initialized
[   20.812785] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.892601] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   20.896075] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   21.356204] BTRFS: device fsid 7d18474d-e990-412f-a557-b3c0a0b49e44 devid 1 transid 266 /dev/sda1
[   22.373899] device eth0 entered promiscuous mode
[   22.374867] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.396669] device eth2 entered promiscuous mode
[   22.483100] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.787192] ath: EEPROM regdomain: 0x8114
[   22.787199] ath: EEPROM indicates we should expect a country code
[   22.787203] ath: doing EEPROM country->regdmn map search
[   22.787206] ath: country maps to regdmn code: 0x37
[   22.787209] ath: Country alpha2 being used: DE
[   22.787211] ath: Regpair used: 0x37
[   22.787215] ath: regdomain 0x8114 dynamically updated by user
[   22.787252] ath: EEPROM regdomain: 0x8114
[   22.787255] ath: EEPROM indicates we should expect a country code
[   22.787258] ath: doing EEPROM country->regdmn map search
[   22.787260] ath: country maps to regdmn code: 0x37
[   22.787263] ath: Country alpha2 being used: DE
[   22.787265] ath: Regpair used: 0x37
[   22.787268] ath: regdomain 0x8114 dynamically updated by user
[   24.370991] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   24.394176] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[   25.817535] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.818454] br-lan: port 1(eth0) entered forwarding state
[   25.818480] br-lan: port 1(eth0) entered forwarding state
[   25.818524] br-lan: port 2(eth2) entered forwarding state
[   25.818535] br-lan: port 2(eth2) entered forwarding state
[   25.819168] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   25.873448] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   25.888734] device wlan1 entered promiscuous mode
[   25.888775] br-lan: port 3(wlan1) entered forwarding state
[   25.888792] br-lan: port 3(wlan1) entered forwarding state
[   25.921063] device wlan1 left promiscuous mode
[   25.921114] br-lan: port 3(wlan1) entered disabled state
[   27.810955] br-lan: port 2(eth2) entered forwarding state
[   27.810992] br-lan: port 1(eth0) entered forwarding state

b) After a reboot the mSATA-SSD is gone.

[    7.555415] exFAT: Version 1.2.9
[    7.573033] JFS: nTxBlock = 8192, nTxLock = 65536
[    7.634135] SGI XFS with security attributes, no debug enabled
[    7.641605] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.648447] ehci-platform: EHCI generic platform driver
[    7.654077] ehci-orion: EHCI orion driver
[    7.658196] orion-ehci f1058000.usb: EHCI Host Controller
[    7.663634] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    7.671300] orion-ehci f1058000.usb: irq 39, io mem 0xf1058000
[    7.690851] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    7.697044] hub 1-0:1.0: USB hub found
[    7.700813] hub 1-0:1.0: 1 port detected
[    7.705840] uhci_hcd: USB Universal Host Controller Interface driver
[    7.715316] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.720652] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    7.728265] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.736837] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[    7.742850] hub 2-0:1.0: USB hub found
[    7.746619] hub 2-0:1.0: 1 port detected
[    7.750646] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.755990] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    7.763529] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.771853] hub 3-0:1.0: USB hub found
[    7.775623] hub 3-0:1.0: 1 port detected
[    7.779692] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.785042] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    7.792644] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.801214] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[    7.807214] hub 4-0:1.0: USB hub found
[    7.810996] hub 4-0:1.0: 1 port detected
[    7.815017] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.820344] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    7.827883] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.836201] hub 5-0:1.0: USB hub found
[    7.839970] hub 5-0:1.0: 1 port detected
[    7.845143] usbcore: registered new interface driver usb-storage
[    8.185361] init: - preinit -
[   11.233590] mount_root: mounting /dev/root
[   11.238637] BTRFS info (device mmcblk0p1): disk space caching is enabled
[   11.246004] mount_root: loading kmods from internal overlay
[   11.456455] block: attempting to load /etc/config/fstab
[   11.462507] block: extroot: not configured
[   11.468933] procd: - early -
[   11.471856] procd: - watchdog -
[   11.575058] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.601683] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.637013] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.661405] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.697220] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.721769] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.757211] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.781663] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.817122] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.841606] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   12.042454] procd: - ubus -
[   13.047479] procd: - init -
[   13.106328] marvell-cesa f1090000.crypto: CESA device successfully registered
[   13.119366] NET: Registered protocol family 38
[   13.135088] md: linear personality registered for level -1
[   13.140992] md: raid0 personality registered for level 0
[   13.147279] md: raid1 personality registered for level 1
[   13.153486] md: raid10 personality registered for level 10
[   13.159338] async_tx: api initialized (async)
[   13.166669] md: raid6 personality registered for level 6
[   13.172011] md: raid5 personality registered for level 5
[   13.177334] md: raid4 personality registered for level 4
[   13.184477] FS-Cache: Loaded
[   13.187804] md: multipath personality registered for level -4
[   13.194733] NET: Registered protocol family 8
[   13.199101] NET: Registered protocol family 20
[   13.207287] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[   13.218122] Key type dns_resolver registered
[   13.225237] NET: Registered protocol family 33
[   13.229693] Key type rxrpc registered
[   13.233382] Key type rxrpc_s registered
[   13.240357] kAFS: Red Hat AFS client v0.1 registering.
[   13.245566] FS-Cache: Netfs 'afs' registered for caching
[   13.280203] RPC: Registered named UNIX socket transport module.
[   13.286167] RPC: Registered udp transport module.
[   13.290892] RPC: Registered tcp transport module.
[   13.295606] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.319960] NFS: Registering the id_resolver key type
[   13.325079] Key type id_resolver registered
[   13.329271] Key type id_legacy registered
[   13.333907] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   13.343122] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   13.352991] RxRPC: Registered security type 2 'rxkad'
[   13.369541] tun: Universal TUN/TAP device driver, 1.6
[   13.374630] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.384401] sit: IPv6 over IPv4 tunneling driver
[   13.390992] gre: GRE over IPv4 demultiplexor driver
[   13.396601] ip_gre: GRE over IPv4 tunneling driver
[   13.416503] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   13.425117] PPP generic driver version 2.4.2
[   13.432771] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.443718] cryptodev: driver 1.8 loaded.
[   13.451533] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   13.459558] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   13.533062] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   13.538940] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.714354] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   13.725096] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.734865] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.743993] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   13.754388] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.763982] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.780676] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 19b6:d03c
[   13.789957] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.799534] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   13.844293] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[   13.851413] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.861884] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.871553] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.880461] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   15.007502] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   15.091312] ath: EEPROM regdomain: 0x0
[   15.091316] ath: EEPROM indicates default country code should be used
[   15.091319] ath: doing EEPROM country->regdmn map search
[   15.091323] ath: country maps to regdmn code: 0x3a
[   15.091326] ath: Country alpha2 being used: US
[   15.091329] ath: Regpair used: 0x3a
[   15.096851] u32 classifier
[   15.099568]     input device check on
[   15.103257]     Actions configured
[   15.109488] Mirror/redirect action on
[   15.114896] GACT probability on
[   15.122790] netem: version 1.3
[   15.131167] fuse init (API version 7.23)
[   15.146894] usbcore: registered new interface driver cdc_wdm
[   15.155564] Ebtables v2.0 registered
[   15.160491] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.172421] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   15.324206] Netfilter messages via NETLINK v0.30.
[   15.329759] PPP MPPE Compression module registered
[   15.335079] NET: Registered protocol family 24
[   15.342946] usbcore: registered new interface driver ums-alauda
[   15.349621] usbcore: registered new interface driver ums-cypress
[   15.356555] usbcore: registered new interface driver ums-datafab
[   15.363372] usbcore: registered new interface driver ums-freecom
[   15.370243] usbcore: registered new interface driver ums-isd200
[   15.377174] usbcore: registered new interface driver ums-jumpshot
[   15.384118] usbcore: registered new interface driver ums-karma
[   15.391159] usbcore: registered new interface driver ums-sddr09
[   15.397985] usbcore: registered new interface driver ums-sddr55
[   15.404948] usbcore: registered new interface driver ums-usbat
[   15.416699] usbcore: registered new interface driver usbserial
[   15.422589] usbcore: registered new interface driver usbserial_generic
[   15.429157] usbserial: USB Serial support registered for generic
[   15.443931] xt_time: kernel timezone is -0000
[   15.462144] usbcore: registered new interface driver cdc_ether
[   15.472515] ctnetlink v0.93: registering with nfnetlink.
[   15.481462] usbcore: registered new interface driver qmi_wwan
[   15.488390] usbcore: registered new interface driver rndis_host
[   15.501910] pci 0000:00:03.0: enabling device (0140 -> 0142)
[   15.513986] ath: EEPROM regdomain: 0x0
[   15.513990] ath: EEPROM indicates default country code should be used
[   15.513993] ath: doing EEPROM country->regdmn map search
[   15.513997] ath: country maps to regdmn code: 0x3a
[   15.514000] ath: Country alpha2 being used: US
[   15.514002] ath: Regpair used: 0x3a
[   15.520796] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   15.522278] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xf1d40000, irq=109
[   15.530758] usbcore: registered new interface driver option
[   15.536415] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.544093] usbcore: registered new interface driver qcserial
[   15.549884] usbserial: USB Serial support registered for Qualcomm USB modem
[   18.423692] random: nonblocking pool is initialized
[   20.829403] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.912539] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   20.916016] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   22.317958] device eth0 entered promiscuous mode
[   22.319317] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.336490] device eth2 entered promiscuous mode
[   22.422344] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.775705] ath: EEPROM regdomain: 0x8114
[   22.775713] ath: EEPROM indicates we should expect a country code
[   22.775717] ath: doing EEPROM country->regdmn map search
[   22.775720] ath: country maps to regdmn code: 0x37
[   22.775723] ath: Country alpha2 being used: DE
[   22.775726] ath: Regpair used: 0x37
[   22.775729] ath: regdomain 0x8114 dynamically updated by user
[   22.775767] ath: EEPROM regdomain: 0x8114
[   22.775770] ath: EEPROM indicates we should expect a country code
[   22.775772] ath: doing EEPROM country->regdmn map search
[   22.775775] ath: country maps to regdmn code: 0x37
[   22.775777] ath: Country alpha2 being used: DE
[   22.775780] ath: Regpair used: 0x37
[   22.775782] ath: regdomain 0x8114 dynamically updated by user
[   24.310933] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   24.350928] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[   25.818496] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.820027] br-lan: port 1(eth0) entered forwarding state
[   25.820056] br-lan: port 1(eth0) entered forwarding state
[   25.820095] br-lan: port 2(eth2) entered forwarding state
[   25.820105] br-lan: port 2(eth2) entered forwarding state
[   25.821254] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   25.869791] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   25.882180] device wlan1 entered promiscuous mode
[   25.882220] br-lan: port 3(wlan1) entered forwarding state
[   25.882251] br-lan: port 3(wlan1) entered forwarding state
[   26.810976] br-lan: port 3(wlan1) entered disabled state
[   27.364171] wlan0: authenticate with 64:d1:54:a2:1d:36
[   27.371178] wlan0: send auth to 64:d1:54:a2:1d:36 (try 1/3)
[   27.371604] wlan0: authenticated
[   27.380914] wlan0: associate with 64:d1:54:a2:1d:36 (try 1/3)
[   27.382883] wlan0: RX AssocResp from 64:d1:54:a2:1d:36 (capab=0x431 status=0 aid=2)
[   27.384154] wlan0: associated
[   27.384249] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   27.810874] br-lan: port 2(eth2) entered forwarding state
[   27.810921] br-lan: port 1(eth0) entered forwarding state
[   33.093784] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   33.093859] br-lan: port 3(wlan1) entered forwarding state
[   33.093883] br-lan: port 3(wlan1) entered forwarding state
[   35.090846] br-lan: port 3(wlan1) entered forwarding state

c) After the next reboot Wifi-Card 2Ghz and msata cards are no longer there.

[    5.021654] Waiting 2 sec before mounting root device...
[    7.033641] BTRFS: device fsid 8bce2376-f3be-45ef-b0fa-b62236e9bd02 devid 1 transid 182 /dev/root
[    7.043123] BTRFS info (device mmcblk0p1): disk space caching is enabled
[    7.049840] BTRFS: has skinny extents
[    7.057229] BTRFS: detected SSD devices, enabling SSD mode
[    7.100850] VFS: Mounted root (btrfs filesystem) on device 0:13.
[    7.106996] Freeing unused kernel memory: 284K
[    7.158439] init: Console is alive
[    7.161919] init: - watchdog -
[    7.516398] usbcore: registered new interface driver usbfs
[    7.521964] usbcore: registered new interface driver hub
[    7.527322] usbcore: registered new device driver usb
[    7.534231] exFAT: Version 1.2.9
[    7.551998] JFS: nTxBlock = 8192, nTxLock = 65536
[    7.612838] SGI XFS with security attributes, no debug enabled
[    7.620268] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.627156] ehci-platform: EHCI generic platform driver
[    7.632788] ehci-orion: EHCI orion driver
[    7.636906] orion-ehci f1058000.usb: EHCI Host Controller
[    7.642346] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[    7.649994] orion-ehci f1058000.usb: irq 39, io mem 0xf1058000
[    7.670843] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[    7.677035] hub 1-0:1.0: USB hub found
[    7.680806] hub 1-0:1.0: 1 port detected
[    7.685848] uhci_hcd: USB Universal Host Controller Interface driver
[    7.695376] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.700711] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    7.708330] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.716903] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[    7.722919] hub 2-0:1.0: USB hub found
[    7.726689] hub 2-0:1.0: 1 port detected
[    7.730714] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.736056] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[    7.743616] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.751941] hub 3-0:1.0: USB hub found
[    7.755709] hub 3-0:1.0: 1 port detected
[    7.759775] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.765123] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    7.772724] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.781295] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[    7.787290] hub 4-0:1.0: USB hub found
[    7.791071] hub 4-0:1.0: 1 port detected
[    7.795093] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.800420] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[    7.807961] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.816279] hub 5-0:1.0: USB hub found
[    7.820047] hub 5-0:1.0: 1 port detected
[    7.825219] usbcore: registered new interface driver usb-storage
[    8.165230] init: - preinit -
[   11.216898] mount_root: mounting /dev/root
[   11.221965] BTRFS info (device mmcblk0p1): disk space caching is enabled
[   11.229322] mount_root: loading kmods from internal overlay
[   11.439209] block: attempting to load /etc/config/fstab
[   11.445306] block: extroot: not configured
[   11.451781] procd: - early -
[   11.454687] procd: - watchdog -
[   11.555157] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.581839] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.617605] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.642210] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.677953] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.702650] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.738433] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.763091] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.798439] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   11.822874] random: jshn: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[   12.022321] procd: - ubus -
[   13.031906] procd: - init -
[   13.090717] marvell-cesa f1090000.crypto: CESA device successfully registered
[   13.103845] NET: Registered protocol family 38
[   13.120098] md: linear personality registered for level -1
[   13.126218] md: raid0 personality registered for level 0
[   13.132318] md: raid1 personality registered for level 1
[   13.138491] md: raid10 personality registered for level 10
[   13.144359] async_tx: api initialized (async)
[   13.151700] md: raid6 personality registered for level 6
[   13.157028] md: raid5 personality registered for level 5
[   13.162361] md: raid4 personality registered for level 4
[   13.169517] FS-Cache: Loaded
[   13.172873] md: multipath personality registered for level -4
[   13.179799] NET: Registered protocol family 8
[   13.184178] NET: Registered protocol family 20
[   13.192407] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[   13.203243] Key type dns_resolver registered
[   13.210372] NET: Registered protocol family 33
[   13.214844] Key type rxrpc registered
[   13.218514] Key type rxrpc_s registered
[   13.225509] kAFS: Red Hat AFS client v0.1 registering.
[   13.230698] FS-Cache: Netfs 'afs' registered for caching
[   13.265132] RPC: Registered named UNIX socket transport module.
[   13.271083] RPC: Registered udp transport module.
[   13.275797] RPC: Registered tcp transport module.
[   13.280509] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   13.304812] NFS: Registering the id_resolver key type
[   13.309899] Key type id_resolver registered
[   13.314128] Key type id_legacy registered
[   13.318774] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   13.328016] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   13.337794] RxRPC: Registered security type 2 'rxkad'
[   13.354498] tun: Universal TUN/TAP device driver, 1.6
[   13.359565] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   13.369383] sit: IPv6 over IPv4 tunneling driver
[   13.376247] gre: GRE over IPv4 demultiplexor driver
[   13.381832] ip_gre: GRE over IPv4 tunneling driver
[   13.401735] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   13.411318] PPP generic driver version 2.4.2
[   13.418945] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.431514] cryptodev: driver 1.8 loaded.
[   13.439191] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   13.447250] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   13.520748] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   13.526639] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.704321] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   13.715054] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.724869] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.733992] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   13.744377] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.753973] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.770664] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 19b6:d03c
[   13.779935] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.789540] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   13.834271] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[   13.841386] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.851851] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.861550] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.870459] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.997465] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[   15.081289] ath: EEPROM regdomain: 0x0
[   15.081294] ath: EEPROM indicates default country code should be used
[   15.081296] ath: doing EEPROM country->regdmn map search
[   15.081301] ath: country maps to regdmn code: 0x3a
[   15.081303] ath: Country alpha2 being used: US
[   15.081306] ath: Regpair used: 0x3a
[   15.086779] u32 classifier
[   15.089496]     input device check on
[   15.093193]     Actions configured
[   15.099445] Mirror/redirect action on
[   15.104888] GACT probability on
[   15.112792] netem: version 1.3
[   15.121068] fuse init (API version 7.23)
[   15.136757] usbcore: registered new interface driver cdc_wdm
[   15.145479] Ebtables v2.0 registered
[   15.150414] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.162342] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   15.354195] Netfilter messages via NETLINK v0.30.
[   15.359745] PPP MPPE Compression module registered
[   15.365088] NET: Registered protocol family 24
[   15.372960] usbcore: registered new interface driver ums-alauda
[   15.379642] usbcore: registered new interface driver ums-cypress
[   15.386586] usbcore: registered new interface driver ums-datafab
[   15.393412] usbcore: registered new interface driver ums-freecom
[   15.400290] usbcore: registered new interface driver ums-isd200
[   15.407243] usbcore: registered new interface driver ums-jumpshot
[   15.414169] usbcore: registered new interface driver ums-karma
[   15.421216] usbcore: registered new interface driver ums-sddr09
[   15.428044] usbcore: registered new interface driver ums-sddr55
[   15.435013] usbcore: registered new interface driver ums-usbat
[   15.446777] usbcore: registered new interface driver usbserial
[   15.452673] usbcore: registered new interface driver usbserial_generic
[   15.459242] usbserial: USB Serial support registered for generic
[   15.474072] xt_time: kernel timezone is -0000
[   15.492292] usbcore: registered new interface driver cdc_ether
[   15.502676] ctnetlink v0.93: registering with nfnetlink.
[   15.511655] usbcore: registered new interface driver qmi_wwan
[   15.518561] usbcore: registered new interface driver rndis_host
[   15.533222] usbcore: registered new interface driver option
[   15.538849] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.546485] usbcore: registered new interface driver qcserial
[   15.552303] usbserial: USB Serial support registered for Qualcomm USB modem
[   18.427520] random: nonblocking pool is initialized
[   20.836237] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.912525] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   20.915960] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   22.322354] device eth0 entered promiscuous mode
[   22.323332] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.341726] device eth2 entered promiscuous mode
[   22.422293] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.679144] ath: EEPROM regdomain: 0x8114
[   22.679151] ath: EEPROM indicates we should expect a country code
[   22.679154] ath: doing EEPROM country->regdmn map search
[   22.679157] ath: country maps to regdmn code: 0x37
[   22.679160] ath: Country alpha2 being used: DE
[   22.679162] ath: Regpair used: 0x37
[   22.679166] ath: regdomain 0x8114 dynamically updated by user
[   24.310907] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   24.330898] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[   25.685429] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   25.685522] br-lan: port 1(eth0) entered forwarding state
[   25.685555] br-lan: port 1(eth0) entered forwarding state
[   25.685593] br-lan: port 2(eth2) entered forwarding state
[   25.685604] br-lan: port 2(eth2) entered forwarding state
[   25.686850] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   27.680861] br-lan: port 2(eth2) entered forwarding state
[   27.680903] br-lan: port 1(eth0) entered forwarding state

#16

@cynerd:
I have the following setup:

  • Indiegogo-campaign 2GB WIFI-model
  • TOS v3.10 installed a day after it has been released
  • Indiegogo-campaign WLE900VX 7AA in port 00:01.0 setup in bgn-mode with custom firmware-5.bin (https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/hw2.0/10.2.4.70/firmware-5.bin_10.2.4.70.67)
  • WLE1216V5-20 in port 00:02.0 setup in 5GHz-mode
  • never had a problem with a QCA988X-card not comming up before (I own the first TO since Indiegogo and bought a second one around 2 months ago)
  • I have setup main SSIDs on both cards to be able to roam between 5GHz and 2,4GHz
  • haven’t physically moved or even touched router since about 3 days
root@Router:~# lspci
00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
02:00.0 Network controller: Qualcomm Atheros Device 0046
  • demsg-output when WLE900VX 7AA doesn’t come up:
root@Router:~# dmesg
[    4.203984] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[    4.490928] ata2: SATA link down (SStatus 0 SControl 300)
[    4.496365] ata1: SATA link down (SStatus 0 SControl 300)
[    4.721040] i2c /dev entries driver
[    4.725271] at24 1-0054: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
[    4.732047] i2c i2c-0: Added multiplexed i2c bus 1
[    4.736914] i2c i2c-0: Added multiplexed i2c bus 2
[    4.741789] i2c i2c-0: Added multiplexed i2c bus 3
[    4.746653] i2c i2c-0: Added multiplexed i2c bus 4
[    4.751528] i2c i2c-0: Added multiplexed i2c bus 5
[    4.756390] i2c i2c-0: Added multiplexed i2c bus 6
[    4.761263] i2c i2c-0: Added multiplexed i2c bus 7
[    4.768068] i2c i2c-0: Added multiplexed i2c bus 8
[    4.772882] pca954x 0-0070: registered 8 multiplexed busses for I2C mux pca9547
[    4.780451] orion_wdt: Initial timeout 171 sec
[    4.785043] cpu: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[    4.793287] sdhci: Secure Digital Host Controller Interface driver
[    4.799480] sdhci: Copyright(c) Pierre Ossman
[    4.803984] sdhci-pxav3 f10d8000.sdhci: No vmmc regulator found
[    4.809917] sdhci-pxav3 f10d8000.sdhci: No vqmmc regulator found
[    4.860929] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[    4.868380] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.883407] NET: Registered protocol family 10
[    4.888320] NET: Registered protocol family 17
[    4.892803] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    4.905459] Bridge firewalling registered
[    4.909479] 8021q: 802.1Q VLAN Support v1.8
[    4.913743] Registering SWP/SWPB emulation handler
[    4.918878] BTRFS: using crc32c-generic for crc32c
[    4.923941] Btrfs loaded, integrity-checker=on
[    4.928973] mvsw61xx 10.mvsw61xx: Found MV88E6176 at f1072004.mdio-mii:10
[    4.935810] mvsw61xx 10.mvsw61xx: Using indirect addressing
[    4.954061] mmc0: MAN_BKOPS_EN bit is not set
[    4.961661] mmc0: new high speed MMC card at address 0001
[    4.967287] mmcblk0: mmc0:0001 H8G4a▒ 7.28 GiB
[    4.971931] mmcblk0boot0: mmc0:0001 H8G4a▒ partition 1 4.00 MiB
[    4.977936] mmcblk0boot1: mmc0:0001 H8G4a▒ partition 2 4.00 MiB
[    4.983951] mmcblk0rpmb: mmc0:0001 H8G4a▒ partition 3 4.00 MiB
[    4.990830]  mmcblk0: p1
[    5.012040] armada38x-rtc f10a3800.rtc: setting system clock to 2018-05-31 21:05:12 UTC (1527800712)
[    5.022043] Waiting 2 sec before mounting root device...
[    7.033569] BTRFS: device fsid a325ed36-3d66-4a0e-ad1f-82940efc2599 devid 1 transid 634947 /dev/root
[    7.043326] BTRFS info (device mmcblk0p1): disk space caching is enabled
[    7.050043] BTRFS: has skinny extents
[    7.058540] BTRFS: detected SSD devices, enabling SSD mode
[    7.090942] VFS: Mounted root (btrfs filesystem) on device 0:13.
[    7.097088] Freeing unused kernel memory: 284K
[    7.148709] init: Console is alive
[    7.152192] init: - watchdog -
[    7.337896] usbcore: registered new interface driver usbfs
[    7.343453] usbcore: registered new interface driver hub
[    7.348807] usbcore: registered new device driver usb
[    7.354860] uhci_hcd: USB Universal Host Controller Interface driver
[    7.364263] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.369601] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 1
[    7.377226] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.385803] xhci-hcd f10f0000.usb3: irq 46, io mem 0xf10f0000
[    7.391840] hub 1-0:1.0: USB hub found
[    7.395612] hub 1-0:1.0: 1 port detected
[    7.399642] xhci-hcd f10f0000.usb3: xHCI Host Controller
[    7.404984] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[    7.412532] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.420852] hub 2-0:1.0: USB hub found
[    7.424634] hub 2-0:1.0: 1 port detected
[    7.428711] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.434058] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 3
[    7.441655] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[    7.450215] xhci-hcd f10f8000.usb3: irq 47, io mem 0xf10f8000
[    7.456218] hub 3-0:1.0: USB hub found
[    7.459986] hub 3-0:1.0: 1 port detected
[    7.464024] xhci-hcd f10f8000.usb3: xHCI Host Controller
[    7.469352] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[    7.476889] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.485216] hub 4-0:1.0: USB hub found
[    7.488984] hub 4-0:1.0: 1 port detected
[    8.155499] init: - preinit -
[   11.206791] mount_root: mounting /dev/root
[   11.211529] BTRFS info (device mmcblk0p1): disk space caching is enabled
[   11.220537] procd: - early -
[   11.223471] procd: - watchdog -
[   11.314538] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[   11.344366] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[   11.372736] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[   11.401068] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[   11.791985] procd: - ubus -
[   12.796586] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.805649] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.814651] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.823725] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.832722] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.841741] random: ubusd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
[   12.850807] procd: - init -
[   12.913276] NET: Registered protocol family 8
[   12.917646] NET: Registered protocol family 20
[   12.923555] tun: Universal TUN/TAP device driver, 1.6
[   12.928619] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   12.938234] sit: IPv6 over IPv4 tunneling driver
[   12.944955] gre: GRE over IPv4 demultiplexor driver
[   12.950331] ip_gre: GRE over IPv4 tunneling driver
[   12.959973] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[   12.968895] PPP generic driver version 2.4.2
[   12.974880] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.985323] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   12.993398] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   13.064412] pci 0000:00:02.0: enabling device (0140 -> 0142)
[   13.070334] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.202354] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[   13.213095] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.222944] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.232064] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[   13.242458] ath10k_pci 0000:02:00.0: Falling back to user helper
[   13.252076] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[   13.280245] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[   13.290233] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.302159] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.6-00140 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast crc32 6211363e
[   14.550333] ath10k_pci 0000:02:00.0: board_file api 2 bmi_id 0:1 crc32 dd6d039c
[   17.141318] ath10k_pci 0000:02:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
[   17.221372] ath: EEPROM regdomain: 0x0
[   17.221377] ath: EEPROM indicates default country code should be used
[   17.221380] ath: doing EEPROM country->regdmn map search
[   17.221385] ath: country maps to regdmn code: 0x3a
[   17.221388] ath: Country alpha2 being used: US
[   17.221390] ath: Regpair used: 0x3a
[   17.226689] u32 classifier
[   17.229405]     input device check on
[   17.233090]     Actions configured
[   17.239198] Mirror/redirect action on
[   17.244382] GACT probability on
[   17.251537] netem: version 1.3
[   17.259094] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   17.275413] usbcore: registered new interface driver cdc_wdm
[   17.283666] Ebtables v2.0 registered
[   17.288315] ip_tables: (C) 2000-2006 Netfilter Core Team
[   17.433560] Netfilter messages via NETLINK v0.30.
[   17.439047] PPP MPPE Compression module registered
[   17.444233] NET: Registered protocol family 24
[   17.453896] usbcore: registered new interface driver usbserial
[   17.459776] usbcore: registered new interface driver usbserial_generic
[   17.466357] usbserial: USB Serial support registered for generic
[   17.480147] xt_time: kernel timezone is -0000
[   17.497224] usbcore: registered new interface driver cdc_ether
[   17.507364] ctnetlink v0.93: registering with nfnetlink.
[   17.515786] usbcore: registered new interface driver qmi_wwan
[   17.522355] usbcore: registered new interface driver rndis_host
[   17.535969] usbcore: registered new interface driver option
[   17.541614] usbserial: USB Serial support registered for GSM modem (1-port)
[   17.549095] usbcore: registered new interface driver qcserial
[   17.554898] usbserial: USB Serial support registered for Qualcomm USB modem
[   20.433952] random: nonblocking pool is initialized
[   22.849270] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.932621] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   22.936089] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   24.255191] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[   24.257452] device eth2.5 entered promiscuous mode
[   24.257459] device eth2 entered promiscuous mode
[   24.258449] IPv6: ADDRCONF(NETDEV_UP): br-gast: link is not ready
[   24.269125] device eth2.2 entered promiscuous mode
[   24.270538] IPv6: ADDRCONF(NETDEV_UP): br-iot: link is not ready
[   24.292875] device eth0 entered promiscuous mode
[   24.293888] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.384931] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   24.662538] ath: EEPROM regdomain: 0x8114
[   24.662547] ath: EEPROM indicates we should expect a country code
[   24.662550] ath: doing EEPROM country->regdmn map search
[   24.662553] ath: country maps to regdmn code: 0x37
[   24.662557] ath: Country alpha2 being used: DE
[   24.662559] ath: Regpair used: 0x37
[   24.662562] ath: regdomain 0x8114 dynamically updated by user
[   26.250947] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[   26.290930] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[   29.362808] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   29.362888] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[   29.363073] br-lan: port 1(eth0) entered forwarding state
[   29.363090] br-lan: port 1(eth0) entered forwarding state
[   29.363464] br-iot: port 1(eth2.2) entered forwarding state
[   29.363480] br-iot: port 1(eth2.2) entered forwarding state
[   29.363513] br-gast: port 1(eth2.5) entered forwarding state
[   29.363523] br-gast: port 1(eth2.5) entered forwarding state
[   29.363550] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   29.363603] IPv6: ADDRCONF(NETDEV_CHANGE): br-iot: link becomes ready
[   29.363650] IPv6: ADDRCONF(NETDEV_CHANGE): br-gast: link becomes ready
[   29.364193] device wlan0 entered promiscuous mode
[   29.371656] IPv6: ADDRCONF(NETDEV_UP): tun1: link is not ready
[   29.485384] IPv6: ADDRCONF(NETDEV_UP): tun0: link is not ready
[   29.591604] IPv6: ADDRCONF(NETDEV_UP): tun0: link is not ready
[   29.605859] IPv6: ADDRCONF(NETDEV_UP): tun1: link is not ready
[   30.031743] device iot0 entered promiscuous mode
[   30.043625] IPv6: ADDRCONF(NETDEV_UP): iot0: link is not ready
[   30.043644] br-iot: port 2(iot0) entered forwarding state
[   30.043669] br-iot: port 2(iot0) entered forwarding state
[   30.051400] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   30.051481] br-lan: port 2(wlan0) entered forwarding state
[   30.051502] br-lan: port 2(wlan0) entered forwarding state
[   30.135968] device gast0 entered promiscuous mode
[   30.147671] IPv6: ADDRCONF(NETDEV_UP): gast0: link is not ready
[   30.147686] br-gast: port 2(gast0) entered forwarding state
[   30.147704] br-gast: port 2(gast0) entered forwarding state
[   30.151280] IPv6: ADDRCONF(NETDEV_CHANGE): iot0: link becomes ready
[   30.225717] IPv6: ADDRCONF(NETDEV_CHANGE): gast0: link becomes ready
[   31.361056] br-gast: port 1(eth2.5) entered forwarding state
[   31.361105] br-iot: port 1(eth2.2) entered forwarding state
[   31.361120] br-lan: port 1(eth0) entered forwarding state
[   32.040963] br-iot: port 2(iot0) entered forwarding state
[   32.050965] br-lan: port 2(wlan0) entered forwarding state
[   32.140947] br-gast: port 2(gast0) entered forwarding state
[   34.381469] mvneta f1034000.ethernet eth1: Link is Up - 100Mbps/Full - flow control rx/tx
[   34.381495] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
  • delta dmesg when WLE900VX 7AA comes up:
[   13.101016] pci 0000:00:01.0: enabling device (0140 -> 0142)
[   13.106883] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   13.283526] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[   13.294264] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.304106] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[   13.313229] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[   13.323626] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.333240] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[   13.349872] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   13.359145] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   13.368755] ath10k_pci 0000:01:00.0: firmware ver 10.2.4-1.0-00029 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 88595bb8
[   13.413510] ath10k_pci 0000:01:00.0: board id is not exist in otp, ignore it
[   13.420620] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   13.431092] ath10k_pci 0000:01:00.0: Falling back to user helper
[   13.440808] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   13.451157] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   14.580010] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1

  • Yesterday evening I added a new device to the network, a iPhone 7.
    Then after a reboot the WLE900VX 7AA didn’t show up anymore.
  • As it after three reboots still wouldn’t show up, I reverted firmware-5.bin back to default-one. Can’t tell if that was the real trigger but wifi showed up after (4th) reboot and I decided to not reboot again for now (as the WAF of a not showing up wifi is pretty much zero).

I will watch that behaviour like a hawk for the next time and report again if it shows up again…

Update 2018Jun07: The problem is not linked to alternate firmware-5.bin and keeps occuring after each reboot… :frowning: what to do to stop it?


#17

I am also having the same problem.

    root@turris:~# lspci
    00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
    00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
    00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04)
    01:00.0 Network controller: Qualcomm Atheros AR9287 Wireless Network Adapter (PCI-Express) (rev 01)

This happens every time I restart the router.

I correct it manually by removing the file /etc/config/wireless and then it shows up correctly on the web page.

How do I fix this issue? Any help would be appreciated.

Thanks


#18

That unfortunately doesn’t work for me.


#19

@cynerd maybe there was some change in 3.10 update as to how the hardware is utilized? some driver update -> power management -> interference ?


#20

I cannot tell exactly how, but the following is always working: When rebooting disconnect power, wait for some minutes (to cool down the wifi-card in slot 2?), reconnect power.
Maybe the WiFi-card (WLE1216V5-20) gets to hot and won’t come up OR it is the interference-problem @cynerd described. OR maybe both?


#21

Same problem here, radio0 5Ghz is missing since a few days (10 days). It was working fine before.

config wifi-device 'radio0'
	option type 'mac80211'
	option hwmode '11a'
	option path 'soc/soc:pcie-controller/pci0000:00/0000:00:02.0/0000:02:00.0'
	option htmode 'VHT80'
	option country 'FR'
	option txpower '20'
	option channel '36'

But device pci for this radio seems missing:

# lspci -v
00:01.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: bus master, fast devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: e0000000-e00fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00
lspci: Unable to load libkmod resources: error -12

00:02.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: fast devsel
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00

00:03.0 PCI bridge: Marvell Technology Group Ltd. Device 6820 (rev 04) (prog-if 00 [Normal decode])
	Flags: fast devsel
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	Prefetchable memory behind bridge: 00000000-000fffff
	Capabilities: [40] Express Root Port (Slot+), MSI 00

01:00.0 Network controller: Qualcomm Atheros AR9287 Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Qualcomm Atheros Device 30a4
	Flags: bus master, fast devsel, latency 0, IRQ 108
	Memory at e0000000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 3
	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
	Capabilities: [60] Express Legacy Endpoint, MSI 00
	Capabilities: [100] Advanced Error Reporting
	Capabilities: [140] Virtual Channel
	Capabilities: [160] Device Serial Number 00-15-17-ff-ff-24-14-12
	Capabilities: [170] Power Budgeting <?>
	Kernel driver in use: ath9k

Rebooting fixes this issue, but just for a while.
How to fix that ?

best regards,
Edouard


#22

Question: Do you have a kickstarter (revision 01)-board?
If so, its routcause maybe misdesigned capacitors (see post above Omnia 3.10 disappeared Wi-Fi).
As I don’t live in Prague, I desided to circumvent it (by doing cold reboots) until I’ve build my own router-server. Afterwards I will only reboot it as an access point after a software update.


#23

Thank you for your answer. Yes it’s a kickstarter board.

Before Omnia I was using a netgear WNDR3800 that had exactly the same problem after a couple of years. Had to reboot it every day… So I ended up at that time with my own router, but wanted something more robust. That’s why I bought an Omnia, quite expensive. But now, same problem with the Omnia… I guess there is no RMA ?

I will try the heatsink too. Is there a thermal sensor on the ATH wifi board ?


#24

Hello,

Your unit should be still under warranty as for Indiegogo backers, we have extended warranty period to 3 years.
I’ll write to you soon, and we’ll figure it out.


#25

Hi @Pepe,
i’m also indiegogo backers and have same issue, i have only 5GHz and MSATA card installed, but sometimes WLAN disappeared, led PC2 go off. It’s any option how can i connect support to replace, or send debug log?

Omnia - 2GB RAM

Device Turris Omnia - rtrom01
Serial number 47244662344
Turris OS version 3.11.1
Kernel version 4.4.167-4a7a81f8db0ad743e54c68e1845c60b6-1

#26

Hi,

Would you please reach us on tech.support@turris.cz?
If you can send us diagnostics, which you can generate in Foris, when it isn’t working and when it works, it would be good.

I’m not sure if I or somebody else will respond to you this week as many people have a vacation this week including me, however, at the latest you should get the answer by January 2nd.